Welcome to Sage Audio. Today let’s talk about How to Saturate Vocals. But first,
If you have a mix that you need mastered,
send it to us to receive a free mastered sample of it with the link in the description.
Identify Important Hz. Ranges
Before we begin to saturate our vocal, it’s useful to identify
important frequency ranges within the vocal’s signal. The vocal’s fundamentals
will arguably be the most important range - since they’re often the loudest,
they’ll trigger the saturation and be the foundation from which harmonics form.
The majority of harmonics that form from saturation will be in the
low-mids to mids - but if we observe closely, we can pinpoint this range.
Understanding these ranges will be important for the rest of this video - but first,
let’s listen to the vocal without any saturation, and isolate these regions.
2. Complex Saturation with Single Band Saturator
Now that we have a better understanding of our vocal’s important frequency ranges,
let’s start saturating. If we have a single band saturator, tailoring it to the vocal can
be a challenge, but if we place an EQ before the saturator, we can emphasize our important ranges.
This is called an emphasis technique, and it’ll cause the saturator to work
harder on those frequencies, giving us more control over the timbre.
If our EQ offers it, we can make these bands dynamic, causing a dynamic emphasis technique.
Let’s take a listen to the effect.
If you’re enjoying the video, hit the like button and subscribe if you haven’t already;
it’s free and helps us bring you more videos.
3. Converting Single-Band Saturator into MB
If the last technique didn’t offer enough control, and you don’t own a multi-band saturator,
we can use parallel tracks to help with this. Let’s create 3 sends, on each one I’ll first
insert a linear phase EQ and then isolate the lows, mids, and highs respectively.
The crossovers will be set to the important ranges we found in chapter 1.
Then we’ll insert our saturator on each track, and saturate it to varying degrees.
To blend in the effect, we can adjust the send’s channel faders until we get a good balance.
Let’s take a listen to this technique being used. 4. Choosing Saturation Types Carefully
Let’s use the FabFilter Saturn 2 and run a sine wave into it - if
we analyze the response after saturation we’ll notice that each saturation type
creates various harmonic formations which will change the sound of our vocal.
Knowing our vocal’s important ranges, let’s create bands that match these.
Then we can listen very carefully as we select different saturation types.
Depending on the complexity of the plugin you use, different saturation types
will also change the frequency response, and either emphasize or suppress transients.
Let’s listen to 2 different settings and notice how the vocal’s sound changes.
5. Modulating Saturation for Specific Effects Pt. 1
Using this same plugin, we can introduce modulation to emphasize specific ranges
or achieve a unique sound - for example, let’s imagine we want a crisp
hip-hop vocal. Let’s create an envelope follower, change it to transient mode,
and then attach it to the drive dial of the high frequencies.
Now whenever a transient is sung, this range will be emphasized. This is just one way of
many that we can combine modulation and saturation to create specific effects.
6. Modulating Saturation for Specific Effects Pt. 2
Another useful way to modulate MB saturation would be to create a band that isolates 2kHz
to 5kHz. Using an envelope follower as we did in the last chapter, let’s attach it to the drive
dial, and to the overall level of the band, increasing both whenever the vocal is present.
This way the vocal will cut through a dense mix, but in a dynamic way that
can be controlled by altering the ADSR of the envelope follower. Let’s take a listen.
7. Unique Reverberated Saturation
One new technique I’ve been trying recently is isolating the saturation, and then reverberating
it. To do this I’ll use a parallel track and saturate the signal as we did in chapter 3,
and then I’ll insert a reverb plugin with room emulation for a shorter, denser sound.
This will accomplish a couple of things - first, it’ll make the saturation sound unique,
and second, its short reflections will act somewhat like frequency modulation,
creating a denser and blended sound.
Let’s take a listen.
If you're enjoying the channel, use the search box to watch more of our videos.
8. Maximizing Vocal Saturation
After we've saturated the vocal, it helps to bring its quietest details forward - to do this use you
can use an upward compressor or a maximizer. I’ll use Melda Audio’s free compressor plugin,
and increase the value of the signal below the threshold - this will amplify low-level content.
As a result, details of the saturation that were being masked by louder signals
will be made more apparent - making the saturation more complex and full. Let’s listen to this effect
on isolated or parallel saturation so that we can better understand what it’s doing.
In-Key Emphasis Technique
Let’s revisit a concept that we used in chapter 2 - the emphasis technique,
but use it in a more specific or intentional way. What I’ll do is figure out the key of the song,
and then amplify in-key notes using the equalizer, before saturating the vocal.
This way, in-key elements of the vocal are more likely to be saturated,
causing more musical and in-tune saturation. If you try this, it’s best to use saturation
with even-ordered harmonics to ensure all harmonics will be in key as well.
De-essing Prior to Saturation
If you’re saturating the entire frequency range, or maybe performing high frequency
modulated saturation to create a crisp sound like in chapter 5, it’s important to
de-ess first. The de-esser will control the dynamics of these high frequencies,
ensuring the sibilance isn’t inconsistent or too aggressive.
The longer the release on this de-esser, the smoother the sound,
so adjust this as desired and if it’s available with the de-esser you’re using.
Let’s listen to high-frequency saturation with a de-esser inserted before it.
Where to Insert Saturation on a Vocal
When saturating your vocal, it’s important not to place the saturator after temporal processing,
like delay or reverb - otherwise, it’ll have trouble saturating the fundamental
or at least measuring the fundamental properly. That said,
saturating after temporal processing does have a cool and unique effect.
Since we’ve already listened to more conventional saturation routing, Let’s try this out by using
a delay on the vocal and saturating the delay taps to create an interesting sound.
I’ll do this as a parallel track so we can hear the effect isolated to only the delay taps.
If you have a mix that you need mastered, send it to us to receive a free mastered sample of it
with the link in the description. Thank you so much for watching.