Today, we'll be talking about column chromatography.
What is this even useful for?
Well, when drug companies are trying
to produce large amounts of medicine,
they need to be able to use a purification process that
can be done a pretty large scale.
So sometimes in their product, they
need to get just the final active ingredient purified,
and column chromatography is a great way to do that.
So how would we set that up in our organic chemistry lab?
Remember that the stationary phase is the silica gel
or other material inside the column,
and the mobile phase is the solvent that you pour into it.
Well, let's take a look at the equipment.
Shown here in blue, we have the column.
This has a few different parts.
It has an opening at the top where you can pour things in;
a stopcock at the bottom, which I currently
have shown in the closed position;
and also a flask at the bottom to collect
whatever it is you're using.
But it doesn't have to be a flask.
You could use test tubes or really
any other piece of glassware you'd like.
So how do we begin?
First, we need to pack this column full of some kind
of filtration material, but we also
want to make sure that that stuff doesn't just
run through and spill into the flask.
So first, you want to put a little cotton
ball at the very bottom.
This is very small, and usually what you end up doing
is taking a long stick and just kind
of ramming it right up against the stopcock.
Next, what I'd put in is a fine layer of sand.
You want to try to get this to be as horizontal as possible,
not tilted or slanted-- and I'll explain that
later on-- but you want to do that with any layer
you're adding onto the column.
They should all be perpendicular to your column.
Next, what you'd do is add in the silica.
The silica will take up most of your column,
and you would be using that to fill almost all of it,
just pouring it all in until it reaches a line of, say,
about here.
Lastly, you'd pour your solvent into the column
and make sure that the column is kept wet at all times,
because if it runs dry and cracks,
it can cause running and mixing of bands.
So you would have your solvent line at about here,
because if your column dries out it can crack.
And what you'll see is that this is actually going through--
again, as I said-- the whole column.
But this looks a little bit messy,
so let me just clean that up for a minute.
Next, what we'll want to do is load the column
with the actual product that we're using.
And how do we do that?
You can actually drop it in with a pipette, because you
want to make sure that the layer is very even.
So let's draw it out here.
On top, you have this fine layer that you're
dropping in on top of silica gel.
But how can I push this through the column and into the flask?
Well, the first step I'll need to take
is actually just opening up your stopcock.
So why do we need to open up the stopcock?
Well, when you pour in the solvent,
you want the band to start going down the column
and traveling down, and that will only
happen if the liquid can flow out the other end.
So let's redraw your silica line in here.
This is now where your silica is, but as you see,
the original green band has separated
into two distinct bands now.
You can kind of see a yellow one and a blue one.
In real life, the colors might not be quite this distinct,
but you get the idea.
And as this proceeds, again you'll see the silica line,
but the separation between the two bands
will actually become more and more distinct.
And so far what you've been collecting in your flask is
mostly all just solvent, but how do we actually
collect whatever's in the blue band?
And you might not know exactly what compound it is,
but you can tell that by the fact that they're traveling
at different rates, the blue and yellow bands probably
have different polarities and are different compounds.
So when you see that the blue band is getting really
close to the bottom, you'll want to quickly switch out
your old flask for a new one so that you've
collected in the new flask, it's just
this layer of the blue compound, while in your column
you still have the yellow layer.
Note that each flask you collect is considered a fraction,
and that's how you conduct column chromatography.
So earlier I was telling you want to make sure
that these are pretty much horizontal,
but what happens if instead when you're packing your column
or pouring something in, it ends up looking kind of crooked?
So in this case, let's say that our column was pretty crooked,
what you would see instead, this is the silica line.
But as those two bands traveled through, instead of seeing
them just parallel to one another,
and again perfectly perpendicular to your column,
what you'd see is something that looks more like this.
You have the yellow band kind of slanted,
then you'd also have the green band
slanted if you had loaded in your compound
in the slanted manner.
And the issue with this is that at a certain time point,
say if you're trying to collect the fraction that
falls between here and here, you're not really
getting the pure yellow compound or the pure green compound.
Instead, you're getting a mixture
of the two, which shows that this
isn't a very efficient purification.
So what you'll want to do next time
is be very careful in the initial stages,
because a lot of the work with column chromatography
is making sure that you prep it just right.
And the rest is just waiting and letting your solvent run
through.
So let's review what we learned today.
We learned how to pack a column using cotton, sand,
and silica gel.
And we also learned how to separate compounds using column
chromatography based on their polarities.