Hi, Travis with POSGuys.com.
Today we're reviewing Zebra's latest 2-inch printer, the ZD410.
This is the only 2-inch printer that they're going to make going forward, and it's a direct
replacement for the older LP2824.
The LP2824 was a great printer, it's been in the market for about 10 years right now,
there's a 2824 plus, there was a TLP version, but overall it was kind of the little engine
that could, it was a small, durable printer, good for printing little address labels or
jewelry labels, things like that.
The ZD410 is an upgrade.
It has a new interface that is much easier to use than the 1 button interface.
Calibrating is much more straightforward, much easier to do.
Loading in the labels is the same way as the old printer, it's a clamshell design, you
release the clips, drop in the media, close the top, and you're ready to print.
It is better than the 2824 because it's now available with more options.
There's new interfaces available, there's Bluetooth, there's WiFi, you can add Ethernet
after you purchase the printer, you can also add cutters of peelers in the field, you don't
have to purchase those ahead of time anticipating that you're going to use it in the future,
you can add them on later on.
The price point on it is similar, the warranty is similar, and then size-wise, it's actually
a little smaller.
Your width is going to be pretty much the same, but the height, it's a little bit shorter.
Overall a little smaller, and overall a little better printer.
There's also a 300 dpi printer version available, which makes jewelry labels able to use a much
more dense barcode, 300 dpi can print finer lines, so you can print very very small, very
very tight barcodes.
So that is a welcome addition to the 2-inch printer line.
Maxiumum print speed on the ZD410 is 4 inches per second if you're printing in 300 dpi mode,
and 6 inches per second if you're printing in 203 dpi mode.
I'm going to print here some sample labels.
This is printing in 300 dpi, so your max print speed is 4 inches per second.
I'm going to print 10 labels.
Changing media and calibrating is a much more simplified process than in the past.
I'm going to take out my short labels here, and we're going to switch them to a black-mark
label.
You drop it in like before, if you want to adjust, there's a little wheel there you can
adjust the absolute thickness of it, you can make it a little wider if you want a little
more play on the wheel.
Close it up.
So to calibrate in the past you had to turn off the printer, hold down the button, turn
on the printer, wait for the light to flash, and then let go.
Now, at any point if you hold down the two buttons on the edge and wait for two seconds
it'll spit out a new label that's calibrated.
Printing the configuration of your printer is much easier too, you just hold down the
two buttons on the side, you'll see some lights blinking, and then it spits out the configuration
of the printer.
300 dpi printing allows some very dense barcodes to be printed, so you can print on a very
small jewelry label, this is the butterfly label, your ring or item goes in the middle,
and then it wraps around the side.
As you can see, I have a very very tiny barcode on it, and in order to print that you do need
300 dpi.
It prints 300 dpi at 4 inches per second, I'll print 5 more labels, and you get high
quality labels on jewelry stock.
This is a big improvement over the old printer, where you couldn't print nearly as dense barcodes
on a jewelry label.
So overall how do we rate the ZD410?
It's an improvement on the 2824, the calibration process is much better, which was one of the
hang ups of the older printer, so overall it's a good buy.
It's definitely cheaper than the 4 inch model, so if you're printing things like jewelry
tags, address labels, you never need to go to that 4 inch print width, then I highly
recommend the ZD410.
It is one of the only 2-inch print width models on the market, so definitely a good buy.
The standard warranty on the ZD410 is 12 months or 1 year.
Extended warranties are also available if you want comprehensive coverage or faster
replacement.
Your standard interface is USB, there are Ethernet, WiFI, Bluetooth, Serial interfaces,
either as add on modules or as optional models to be purchased.
This is the healthcare white version, it's plastic can also be sprayed down so you can
sterilize it.
The grey version is also available, that's a little less, it's just your standard retail
version that can't be sprayed down as well, the plastic is normal plastic on it.
For more information on this printer, to purchase the printer, to purchase supplies for it,
please visit us at POSGuys.com.
Thanks!