Shell Deep Water is fueling the growth of Upstream Americas
by safely developing new reserves
and maximizing the potential of its existing producing assets
in the Gulf of Mexico, Brazil, and Venezuela.
Drilling a safe, deep water well
can take years of planning and preparation.
After identifying potential oil and natural gas reservoirs 8 00:00:25,900 --> 00:00:29,100 beneath the seafloor using seismic technology
a drill site is selected.
Shell geoscientists choose the drill site location on the seafloor
based upon the safest well path
that will encounter the targeted oil and natural gas.
For an exploratory well
in water depths up to 9000 feet deep
this seafloor location is generally directly above the reservoir.
A drilling rig is required to drill a well
In deepwater, the rig may be on one of three vessels:
a Drillship
a Semi-submersible vessel
or it may be part of a floating production platform.
All rigs have a hoisting system to raise and lower the drill pipe
and tools needed to drill the well,
a Blow Out Preventer or BOP stack, 24 00:01:16,500 --> 00:01:17,900 and a pumping system
to circulate fluids in and out of the well while drilling
It’s time to drill the hole or well bore using a drill bit.
This initial step is called “spudding in” the well.
The shallow sediments just below the seafloor are often very soft and loose.
To keep the well from caving in and carry the weight of the wellhead,
a large diameter base pipe or casing is drilled or jetted into place.
The base pipe is assembled at the rig floor
and a drill bit connected to a drill pipe
is run thru the inside to the bottom of the casing.
The entire assembly is lowered to the seafloor by the rig hoist.
At the seafloor
the driller “spuds" the assembly into the seafloor sediments
then turns on the pump.
Water or a drill fluid is used to “Jet” the pipe into place
until the wellhead is just above the seafloor.
With the base pipe and wellhead at the right depth
the driller will release the bit
and drill string from the jet pipe and drill ahead.
While the well bore is being drilled
mud is pumped from the surface down through the inside of the drill pipe,
the mud passes through the jets in the drill bit,
and travels back to the seafloor through the space between the drill bit
and the walls of the hole.
Drilling mud is used to
1) lift rock cuttings from the hole,
2) keep the drill bit cool and lubricated
and 3) fill the well bore with fluid to equalize pressure
and prevent water or other fluids in underground formations
from flowing into the well bore during drilling.
The “mud” is an environmentally friendly water based mixture of clay for thickness
and fine ground rock or barite for weight.
At the planned depth
the driller will stop drilling and pull the bit out of the hole.
A smaller pipe or casing string is then screwed together
connected to the drill pipe
and run down to the seafloor and into the well.
To permanently secure the casing in place,
cement followed by mud
is then pumped down the inside of the drill pipe.
To separate the cement from the mud, a cementing plug is used.
The plug is pushed by the mud to ensure the cement is placed outside of the casing
filling the annular space between the casing and the open hole wall.
On some locations a second surface casing is needed,
thus the well is drilled even deeper
In this second surface casing interval
the well is cemented using a second smaller casing string.
Repeating the same process used in the last hole section.
At this point in the well
the pressure in the deeper rock
may be too high to continue with the simple water based clay mud
or there may be the potential to encounter oil or gas.
Before drilling below this point
a Blowout Preventer with a riser will be installed at the seafloor.
The BOP stack is a massive system of valves and rams
that protect the rig and environment from oil and gas flows
should the weight of the drilling mud be too low.
The BOP stack is connected to a pipe called a riser.
The riser connects the rig to the well
and allows us to circulate the drilling fluid
and rock cuttings all the way back to the rig on the surface.
The BOP stack is fully tested before we drill further.
Drilling now resumes with the drill bit
and drill pipe always operating through the BOP stack.
Just as we did further up the hole,
casing strings are run and cemented in place
when needed to cover up the open hole sections
When the oil and gas zones targeted by the geologists are reached
and the presence of an oil or gas zone is proven,
a final casing string may be installed
if the seafloor location is favorable for future development.
This final casing string allows for the future safe production
of the oil and natural gas.