Hello folks, Kirk and Jason here with, Kirk Giordao plastering, I'm gonna show you folks
today is Mel installed this window here he's gonna do this one another date as I was talking
to him I said well gee they're going to install the windows do that and we'll come in and we'll
we'll do the breakout we'll prep it for you what we're doing is the Bulldogs we're gonna break
all the perimeter stuff go out or actually case it's probably gonna do that while I go
clean the truck okay what I what I told him he sent me a picture the other day and I said man
sacrifice the sawzall blade meaning he said well I'll just destroy these that's the nylon if you
destroy these moulds it'll take about six hours to try to find these molds miter these corners
put them all back look at a couple hundred bucks to do that but sacrifice a blade 15 bucks and cut
them as best you can and get them off for all night we'll reuse them we are gonna reuse them
when we get to that state but anyhow what we're gonna do today is we're just gonna tie this in
well after day does all the breakout here then we're gonna come and pay for it and fella Jesse
called me was asking about this windows Jesse who's what I was trying to explain here's the
existing paper of the house this existing paper goes here and the new paper goes on top of that
just like that and with us what we're gonna do is after here's the existing paper of the house
itself now it's got paper back here too so we got one layer to layer this layer is going to go over
the existing layer then we're going to come here and put two more layers over that we are going to
go over the existing paper here there's one layer to layer and this one so we're going to put our
new paper over this paper here we're gonna wire it back together and tie it all in that's what
we're gonna do today and another day we're gonna come back to this stuff away anyhow real simple I
just wanted to point yourself because I get a lot of folks who say gee when we do the paper
how do we do the papers and that's basically it but this window wasn't here you would put your
craft paper down or whatever membrane you're doing you're putting on the bottom you overlap the side
and you put your window it and a lot of times you can just put your flashing paper directly
on top for Zee flash and every windows different Marvins peláez Anderson's I believe these are mill
card some come with a Z flash and some don't anyhow they come with it that means put it on
so we're gonna go ahead and paper this up J's gonna break out then we'll show you all of it
hey guys I took off my mask for a second so you can hear what I'm doing but if you're if you're
doing this stuff definitely wear a mask you don't want to breathe it in what I'm doing is using our
Bosch bulldogs we got to get two to three inches of paper and wire exposed so we can get a full
waterproof client as well as not end up with a huge perimeter crack when we actually stucco this
another tip to guys I didn't see it that happened when this header was put in here it's cracked so
if i just repaired this nasty cracker so taking it out okay guys now what we're gonna do is this is a
stud house stud wall so I'm right on the stud here right on the board if I go back another half inch
I'm gonna be in an open wall it's almost next to impossible to seal an open wall so what I'm doing
is I'm right on the stud here now I put this sick of black nasty stuff don't get it on you great
polyurethane coffee though and what I'm doing is I'm gonna place this on here it's kind of like a
bicycle to do like so and my tie it isn't isn't as well as I might we don't like to get three to
six inches but it doesn't allow it doesn't allow it then I take my knife here and this way when
this dries right here I've got to wire it give us a little better seal than if we didn't use
the coffee the coffee only takes about 15 minutes then we're now we're gonna coffee perimeter here
to anyway we're getting back all right guys we are complete with this every six inches on stud with
the gun I'm using sell for a wire with no foot wire beat you don't beat 30 nails so further it
brings it out of the wall quarter is polyurethane caulking around the perimeters I generally do the
sides the top doesn't need it because it has a plan a lot of times I'll hit underneath here
just a real important part of this is getting our existing paper or you pay under the existing what
I had to do is take a pry bar and pull it up just a little bit I want to pull it up too much I'll
do another crack somewhere along the line in it as soon as I end up taking off about eight
inches extra so you just showed up a little bit got a shooter your paper under there it
will go it takes a bit of practice but anyway it does work heyhow yes then there is the way also
to place the wire there's only one direction it can't go backwards otherwise it's bird the wrong
way anyhow my name is Kirk I was searched on a plastic thank you folks for watching hopefully
you learned how to install these windows and do the paper and wire correctly, My name is Kirk,
Jason, and I thank you for watching, and as usually, we’ll see you on the next one.