Dams serve a wide variety of purposes from hydropower to flood control to storage of
water for municipal and industrials uses.
But when a dam’s useful purpose fades away, the structure itself still remains.
Dams come in all shapes and sizes, but contrary to what you might think, the most dangerous
dams are often the smallest.
Hey I’m Grady and this is Practical Engineering.
Today we’re talking about the dangers of low-head dams.
This video is sponsored by Squarespace.
Visit Squarespace.com/PracticalEngineering to get a free trial, and use code PracticalEngineering
to get an additional 10% off.
More on that later.
A low head dam, sometimes simply called a weir, is a small structure that impounds a
small amount of water and spans the width of river or stream.
Usually made from concrete, the purpose of a low head dams is to raise the water level
upstream on a river.
This can assist with navigation of the channel by boats, create a drop for generating hydropower,
and make water available at intakes for water supply and irrigation.
Thousands of these structures have been constructed over the years to take advantage of natural
watercourses and rivers.
The heyday of low head dam construction was actually in the 1800s when mills and factories
often relied on waterpower to drive grinding wheels and other equipment.
This was at a time when moving water was the most consistent source of power available
in large quantities before widespread adoption of electricity.
Most of these old mills and factories are long gone, and the ones that still survive
certainly don’t depend on water for power anymore.
That means many property owners are forced to maintain these old structures that no longer
have any practical use.
Or more commonly and much worse, these dams are abandoned by their owner and gradually
fall into disrepair.
In the U.S., dam safety regulations focus primarily on the possibility of a dam breaching
and causing a flood wave downstream.
But, because low head dams are relatively short, a breach poses minimal danger, so most
states don’t keep track of these small structures.
And, especially if they’ve been abandoned, it can be difficult to enforce maintenance
requirements on the owners.
But, even though they pose little danger in the event of a breach, low head dams create
a public safety issue that has caused more fatalities in the U.S. than all dam failures
in the past 20 years.
To understand why, we first need to know a little bit about open channel hydraulics.
If you haven’t seen my video about hydraulic jumps, I’ll summarize it here.
Go back and check out that video if you want to learn more.
Open channel flow - that’s flow not confined within a pipe - has a very important property
related to its velocity that governs its behavior.
Slow, tranquil flowing water is called subcritical because waves propagate faster than the flow
velocity.
Fast moving water is supercritical because waves move slower than the flow velocity.
Any time a supercritical flow encounters subcritical flow, an interesting phenomenon called a hydraulic
jump is formed.
Low head dams almost always have subcritical flow upstream.
The flow is deep, slow, and tranquil as it makes its way to the dam.
But as the flow passes over the weir, it picks up speed and becomes supercritical.
When this supercritical flow transitions back to subcritical flow in the slower moving water
downstream, it creates a hydraulic jump as you can see here in my model flume.
It’s easy to see why these types of structures could pose a threat to those using the waterway
for recreation.
Any location with fast moving water and high turbulence can be dangerous to swimmers or
kayakers, but the location of this hydraulic jump can turn a manageable risk into an almost
surefire way to drown.
The depth of the flow downstream of a dam is called the tailwater, and it controls the
location of the hydraulic jump.
In my model, I can adjust the elevation of the tailwater by adding or removing these
stoplogs.
When tailwater is low, the hydraulic jump forms away from the dam.
This is a fully developed jump that follows the traditional shape and flow patterns.
If I send down this piece of wood as a kayaker surrogate, it experiences some turbulence
as it passes over the weir and through the jump but, it doesn’t have much trouble escaping
downstream.
But, as the tailwater rises the jump moves closer and closer to the dam.
Eventually if the tailwater is high enough, the hydraulic jump will reach the dam.
This condition is called a submerged or drowned jump.
It may look fairly innocuous, but this is when things get dangerous.
Let’s send down our kayaker surrogate to see why.
A submerged hydraulic jump creates an area of recirculation immediately downstream of
the dam sometimes called a “keeper” for obvious reasons.
The jet of the hydraulic jump surfaces downstream causing a boil point.
Sometimes this is easy to see and sometimes it’s not.
Either way, objects or people can will only be able to escape a submerged hydraulic jump
if they are able to get beyond this boil point.
And, any rescuers who approach a submerged jump from downstream run the risk of being
drawing into the hydraulic themselves.
The recirculating currents that trap recreators is dangerous enough on its own but there are
other factors contributing to the danger at low head dams.
These currents also trap large debris between the strong hydraulic forces and the hard concrete
surface of the dam which can batter someone trapped in the keeper.
The water is often cold, increasing the potential for hypothermia and further disorientation.
The turbulence of the hydraulic jump entrains a lot of air, reducing the buoyancy of a swimmer.
And, low head dams often span the entire width of the river, meaning there is no still water
nearby that can be used as a safe haven.
This is exactly why the low head dam is called the perfect drowning machine.
All these factors added together create a situation that’s almost impossible to survive.
There are a lot of ways to mitigate this issue.
The simplest option is just to keep people away from these structures.
Some states require that exclusion zones be established to make sure that kayakers safely
portage dams instead of trying to run them.
Good signage and buoys as warnings can sometimes be enough to keep people safe.
Another option is to modify the structure to reduce the potential for recirculating
currents.
Researchers have proposed various retrofits to existing dams to improve flow conditions
when tailwater is high.
Of course, the most obvious (but also most expensive) way to address the issue is to
remove these dams altogether.
In many cases they are no longer serving an important role, and removing dams can help
restore ecosystems and improve connectivity for aquatic species in addition to removing
a hazard.
If you’re swimming or paddling on a river with a low head dam, don’t underestimate
the danger of these powerful hydraulic forces.
Different flow conditions on the river can dramatically change the behaviour of the hydraulic
jump, as we saw, so be careful.
Thank you for watching and let me know what you think!
If you're new to the channel, you might not know that I have a website too.
It's got a blog post for each video with extra information, a little bit about me, and a
small shop with some t-shirts.
When I first started this channel, I knew I wanted to have a website to serve as the
landing page, but I didn't want to learn web development or spend a bunch of time writing
code.
That's why I chose Squarespace 4 years ago and have been using it ever since.
I don't have to update or patch anything, the templates look awesome, and if I ever
have an issue or question, they have 24/7 365 day support available to help.
This may sound silly, but ever since I first logged onto the Internet as a kid, I knew
I wanted to have my own website.
Squarespace made it simple and easy to fulfill that dream of having my own little corner
of the web.
Take a look at Practical.Engineering, and let me know in the comments what type of stuff
you'd like to see me post there.
If you've got idea to share with the world, Squarespace is offering fans of the channel
a free trial at Squarespace.com/PracticalEngineering.
Use code PracticalEngineering to get an additional 10% off your first purchase.
A dream is just an idea that doesn't have a website yet.
Thank you for watching, and let me know what you think!