When you need to transition from tile to a lower surface covering or directly to concrete,
the Schluter®-RENO-RAMP is a perfect solution! Not only does the profile protect tile edges,
but it also provides a smooth slope that eliminates trip hazards.
The profile is typically installed in commercial applications, including those where wheel
carts are used. The Schluter®-RENO-RAMP-K is a variant of
the RENO-RAMP that does not have an anchoring leg. It is installed up to existing floor
coverings. This is useful for creating transitions without having to disturb the existing flooring.
Certain sizes of the profile can be used to create transitions that comply with the Americans
with Disabilities Act, or “A-D-A”, standards for accessible design.
The profiles are available in anodized aluminum. All of these features make RENO-RAMP an ideal
choice for transitioning from floor tiles to lower surface coverings.
We all know that planning is important with any tile installation. It’s even more critical
when working with profiles. It’s the key to a successful project.
We have selected the tile and profiles and determined the overall layout.
RENO-RAMP will be installed as a transition profile.
The DILEX-KSA profile will be installed where the tile meets the walls to provide a movement
joint.
We selected the RENO-RAMP size according to the thickness and format of the tile that
will be used.
In addition to tile setting tools, we will also need to choose the proper tools to cut
the profiles. This will depend on what material the profile is made of.
For the aluminum RENO-RAMP we will be using a miter saw with a non-ferrous blade.
Aluminum profiles can also be cut using a variable-speed angle grinder with the Schluter-PROCUT-TSM
cutting wheel. A third option is to simply use a hacksaw
with bimetal blade. With the planning complete, let’s prepare
for installation. This sequence may vary depending on the layout
and installer preference. In our demonstration, the RENO-RAMP profiles
are installed directly over the concrete. The Schluter-DITRA-XL uncoupling membrane
will be installed over top of the profile anchoring legs. This will give us a flush
transition from the profile to the concrete. The DILEX-KSA profiles will be installed over
top of the DITRA-XL. First, measure where the RENO-RAMP profile
will be installed. Then, transfer the measurement to the profile.
Keep in mind that we must avoid any overlap of the profile anchoring legs because this
will interfere with the tile installation. We make miter cuts to produce a clean transition
between the RENO-RAMP profiles.
Remember to always observe all safety instructions and standards.
We cut the RENO-RAMP using a miter saw with a non-ferrous blade.
For best results, cut the profile slowly. An accurate cut ensures a clean transition.
Then, file the cut end of the profile to remove any burrs.
Dry fit the profiles.
Now we can move on to the installation.
Using a notched trowel, apply thin-set mortar to the area where the RENO-RAMP profiles will
be installed.
Fill the cavity beneath the sloped section of the profile with thin-set mortar.
Firmly press the anchoring leg of the profile into the thin-set mortar and align.
The next piece of RENO-RAMP is installed the same way. Take care to align the profiles,
paying close attention to the area where the profiles meet.
Always remove any excess setting material immediately from the profile to avoid any
damage to the finish.
Install the DITRA-XL over the area to be tiled, making sure to trowel thin-set mortar over
the profile anchoring legs.
For instructions on how to install Schluter-DITRA-XL, please see the DITRA installation handbook
and video.
The DILEX-KSA profiles are measured and cut.
DILEX-KSA features a self-adhesive strip that allows it to bond to fixed building elements,
such as door and window frames.
Install the DILEX-KSA.
Once the installation of the RENO-RAMP, DITRA –XL and DILEX-KSA is done, we can set the
tile.
Fill the cut back cavities in the DITRA-XL with unmodified thin-set mortar and comb additional
mortar over the matting and DILEX-KSA anchoring legs, using a notched trowel that is appropriate
for the size of the tile.
Solidly embed the tiles into the thin-set mortar, so that the tiled surface is flush
with the surface of the profiles. The profiles should not be higher than the tiled surface,
but rather up to approximately one-thirty-second inch or one millimeter lower.
Set the tile to the RENO-RAMP integrated joint spacer. This will provide a uniform grout
joint.
Don’t forget to clean any excess setting material immediately from the profile to avoid
any damaging the finish.
We complete the installation by setting the remaining tiles.
As you can see, the RENO-RAMP profile is the perfect solution when you need to protect
tile edges and provide smooth transitions to lower surface coverings. Another great
innovation from Schluter®-Systems.