Sleep. Renewal. Refreshment. Revitalization. It's as essential to your well-being as food and water
but your precious sleep is being disrupted and your doctor wants to know why the nomad
sleep recorder enables you to perform a sleep study in the privacy and comfort of your own
home preparing for your sleep study please follow along as we show you the few simple
steps required to setup the Nomad for your sleep study you'll want to start about 30
minutes before bedtime we recommend that you wear comfortable loose-fitting pajamas as the
Nomad will be worn over your clothing since you'll be using medical tape to secure some
of the sensors let's tear off four pieces about two inches long and place them nearby
make sure to remove your jewelry and if you are wearing fingernail polish please remove
that as well finally it's a good idea to turn off any mobile phones kept at
your bedside applying the respiration belts okay let's begin to apply the nomad sensors
To start you'll need to identify the two white respiration belts in your kit place one belt
around your chest just under your armpits holding the large velcro tab at the center of your chest
take a deep breath after you exhale bring the small velcro tab over the larger tab and fasten
the ends so that the belt fits snugly but remains comfortable next surround your waist with the
second belt and as you exhale velcro it securely over your bellybutton can you see the two snaps
on this belt you're going to attach the abdomen sensor to these snaps find the sensor that has a
yellow connector at one end and is labeled a B D for abdomen at the other end are two snaps these
snaps will attach to the snaps you've just found on the belt that's placed around your stomach
next find the sensor that has a blue connector and is labeled chest this sensor will attach to
the belt that's around your chest applying the Nomad recorder now it's time to put on the Nomad
recorder and pouch as you hold it up to you the word Nomad should be facing away from your chest
wrap the belt around your body positioning the Nomad at the center of your chest just below the
chest belt a fix the velcro tab and make sure it fits snugly against you next plug the yellow
connector into its matching colored input on the Nomad recorder the connectors are keyed so they
can be inserted in only one direction you can now plug in the blue chest connector in exactly the
same fashion in addition to being color-coded the ports are also labeled abd and chest
applying the airflow tube and breath sensor now we're ready to connect the airflow tube
and breath sensor which will measure the amount of air you take in and out when you breathe in your
kit you'll find both the airflow tube and a breath sensor which has a green connector simply place
the prongs into your nose and loop the two wires around each ear tighten the wires comfortably
under your chin making certain that you can swallow easily please readjust if necessary next
use two pieces of the medical tape you prepared earlier to secure the airflow tube and breath
sensor wire to your cheek bones then plug the green connector from the breath sensor into its
matching input on the nomad recorder you'll see that this port is also labeled therm the airflow
tube will connect to the white lure lock which is located at the top of the Nomad simply push
it in and twist to the right to make sure it's tightly connected we've labeled this port airflow
applying the finger probe is the last step of our setup ensure that all jewelry and nail polish have
been removed before you do this final step find the sensor that has a rubber tip in which you can
insert your finger if you are right-handed you'll put your left index finger into the rubber tip if
you're left-handed you'll use your right finger insert your finger providing that you've placed
your finger correctly the cable will run along the back of your hand next make a fist and tape
the cable to the back of your hand using the tape you prepared earlier apply another strip of tape
to your forearm so that the cable is securely in place finally just before you're about to climb
into bed plug the finger probe connector gently but firmly into the connector labeled spo2 at
the top of the Nomad about one minute after this last sensor is plugged in you'll notice
a flashing green light that is visible through the front of the pouch this means that the Nomad
has successfully begun recording if you see a red or orange light instead please contact your
service provider before closing the velcro flaps please double check that all the plugs and snaps
are still connected and that your belts are secured all set great then just close all the
flaps on the pouch and make yourself comfortable in bed Nihon codon wishes you a very good night.