Getting that dreaded overvoltage fault can be frustrating but if you understand
what's going on it's pretty easy to fix. First, understand that a variable
frequency drive just takes an AC input voltage, rectifies it, runs that across a
big capacitor to create a DC voltage, which is chopped or pulsed, to send to a
three-phase motor. By adjusting the timing of the pulses across the three
phases the drive can very accurately control the motor speed and direction.
The overvoltage fault is referring to this guy, the DC bus voltage in the drive.
If that voltage goes above what the internal components are rated for, well,
bad things can happen to the drive. So, let's play with this some so we can get a
feel for what's going on. I have this single-phase, 120 volt drive connected to
this motor which has a large cast iron sprocket and hub on it with a combined
weight of about 12 pounds. That'll give us some inertia for the motor to work
against. Inertia is just a measure of how much force is required to accelerate or
decelerate an object. You have to push a lot harder to get something moving than
you do to keep it moving, right? I also have the free WPS software up and
running with a configuration and a resource already set up. My pc is
connected to the drive using this USB comm module. Watch the WPS quick start
video if you need a refresher on how to set all that up. Let's do a factory reset
on the drive so we're starting in a known configuration. These are the motor
parameters and as luck would have it the defaults are fine for this demo, except
the amperage for this motor is 3.2 amps and I've already entered that. Now make
sure your motors numbers are in these parameters, don't use mine. Let's go to
parameter 121 and set the frequency to 60 Hertz which tells the motor to run at
full speed. The acceleration ramp is parameter 100. It looks like it defaults
to 5 seconds. That's fine. Perimeter 101 is a deceleration ramp.
Looks like it defaults to 10 seconds. Let's speed that up a bit to a five-second
deceleration time. Now since the DC bus voltage is the key, let's go down here to
trend, right click to create a new one. I'll call it overvoltage demo. Let's add a
trace. Search on DC and we see the DC link voltage is parameter four. So, I'll select that
that and hit OK twice to add it to our trend. I'm also going to increase the
sample rate to every 50 milliseconds to give us a little more resolution. Well,
click here to get the trend running and press run on the drive to start the
motor spinning. As the motor ramps up to speed, the DC bus voltage sags a little
but now that we're at speed, it's holding steady. That makes sense. I'll press stop
and we see the DC bus voltage rose quite a bit during deceleration. I'll stop the
trend and click these to automatically resize to view. If I put the cursor down
here, we see the DC bus voltage was hanging around this level and if I put
the cursor on the peak, we see the DC bus voltage spiked up to about four hundred
and twenty volts during deceleration. Why does the DC bus voltage go up during
deceleration? Well, when the drive tries to slow the motor down it has to
overcome the inertia built up in this spinning sprocket, so the motor becomes a
generator which forces current back into the drive, which raises the DC bus
voltage. Let's cut the deceleration time in half, which means the drive is gonna
have to work harder to stop the motor in even less time. Start the trend, hit run.
Let it ramp up to speed and settle out and then hit stop. Looks like the bus
voltage got up to 440 volts. That's another 20 volts. Hmm, well let's cut the
deceleration time in half again. Start to trend, hit run. Let it ramp up to speed
and hit stop. Uh oh, what happened? The drive gave us that dreaded overvoltage
fault. Let's stop the trend and we see the DC bus voltage got up to 475 volts
as the drive tried to decelerate that massive pulley. And guess what? If we look
in the programming manual we see that the overvoltage trip point for this
drive is 460 volts. Aha! So that's what the overvoltage fault is all about - the
DC bus voltage getting too high and it's usually caused
by being too aggressive with your deceleration ramp. The cool thing is you
now know how to actually see how close you are to tripping the overvoltage
fault simply by looking at the DC voltage level on a trend while you run
your system. How cool is that? Now there are some other things that can
trip an overvoltage fault. First, since the drive is just rectifying the input
AC voltage, the DC bus is proportional to that input voltage, right? So if the input
voltage is too high, then the DC bus will be too high, so make sure you have the
right AC voltage for your drive. For example, maybe you have 220 coming in but
actually have a 120 drive. Well, that would be bad, right? Second, if you have
some other equipment that's messing with the line voltage that could also cause
an over-voltage fault, put a voltmeter or better yet an oscilloscope on the input
voltage and verify that it really is what you think it should be. Finally, if
you're using dynamic braking and you set the braking threshold above the over
voltage fault level the overvoltage fault will trip before the braking kicks
in which defeats the purpose of dynamic braking. What's dynamic braking? It
watches the DC bus and when it gets too high it simply reroutes the excess
current to an off board resistor so the DC bus can't get too high. That's an
awesome way to get fast deceleration times and protect the drive. We cover
dynamic braking for the WEG CFW300 drive in a separate video. One final note:
do you have to use this WPS software to do this? Well, no. While it's really nice to
be able to see the bus voltage change in real time on a graph, know that you can
always see the last vault in parameter 50, 22 being an overvoltage fault, and
you can see the bus voltage at the last fault in parameter 52. Again, 461 volts is
over the 460 volt overvoltage trip level. And of course you can always just
go to parameter 4, the one we plotted on the trend, and watch the DC bus level
while your system runs. For example, let's change the deceleration ramp to
something bigger so it doesn't fault out on us.
Let's scroll down to parameter 4 so we can watch the bus voltage in real-time.
Hit run, wait for it to ramp up and then hit stop. Sure enough you get a pretty
good idea what's going on. Click here to learn more about the WEG CFW300
variable frequency drive. Click here to learn about Automationdirect's free
award winning support options and click here to subscribe to our YouTube channel
so you'll be notified when we publish new videos.