Welcome to Sage Audio. Today we’re covering how to mix low-end.
But first, if you have a mix that you need mastered
send it to us at SageAudio.com to receive a free mastered sample of it.
Distort Lows with Compression
Distorting your lows can be really helpful, especially when you have multiple instruments
fighting for space in a narrow frequency range.
If we distort the kick, we’ll be able to hear both the kick and bass instruments better
due to how the harmonics from the distortion differentiate them.
To do this I’m going to use a compressor with a very fast attack and release,
and set these to the quickest settings - in turn causing unique but natural sounding distortion.
Transient Shaping Lows
If you’re finding your lows are sounding blurred together, use a transient shaper on your kick or
bass to add some higher frequency content to that signal. I’ll use Elevate by Newfangled audio to
increase the level of my kick’s transients and to separate it from other instruments.
This can be easy to overdo so use your ears and try to keep the effect at a reasonable level.
"If you’re enjoying the video, consider hitting the like button;
it really helps us bring more videos to you"
Inverse EQ Bass and Kick
For this trick we need an EQ that can match signals - we’ll match the kick and bass signals,
and then delete some of the more extreme bands. Then we will highlight all of the bands and
subtly invert their gain, causing everything that match the signals to separate them.
This trick works for other instruments in a similar frequency range,
so try it out whenever needed.
How to Amplify Sub or 808
If you’re mixing a track with subs or 808s, and you want to amplify or attenuate them,
take a look at 20 to 60Hz, which is where these instruments will be situated.
If you want to make your sub or the sine wave of your 808 louder, simply amplify them.
And of course if it’s too loud do the opposite.
How to EQ Kick
Although all kicks are a little different, here are some important frequencies and ranges to
pay attention to when equalizing a kick drum. 40Hz is usually the kick’s fundamental, whereas
80Hz is typically the lowest kick frequency consumer grade speakers will be able to support.
800Hz to 1300Hz is about where you’ll hear the snap of the drum
skin if you’re using organic samples or original recordings. Lastly 4kHz to 6kHz
is where you’ll hear the air of the kick, or the tail end of the kick drum vibration.
Only a small percentage of people that watch our videos are subscribed, so if
you’re enjoying the video, consider subscribing, it’s free, and you can always change your mind
How to EQ Bass Guitar
Bass frequencies will depend on the range, key, and other factors,
so let’s focus on the fundamental and its harmonics - the fundamental is
going to be the strongest frequency and give you the body and warmth of
your bass. The 2nd order harmonic helps the instrument translate to consumer speakers.
The 3rd adds a little clarity to a bass and helps separate it from a kick. Lastly,
from about 1.5 to 2.5kHz you’ll find the most percussive or transient aspects of the bass.
Warm Drum Bus Compression
If you’re mixing a drum bus and it needs compression, try using an internal side-chain
and cutting out the lows from triggering the compressor. This way less compression
occurs and the kick is attenuated less often, causing the drums to have a warm and full tone.
You can also try some saturation
and use tube or transformer settings to emphasis the low end of your drums.
"If you’re interested in advanced mixing and mastering videos, custom plugin presets, and more,
Join and become a member; and if you change your mind, you can always cancel anytime"
Bass on the Side Image
Depending on your processing, bass frequencies can sometimes end up on your side image,
making the mix sound less focused. This can be a good thing and used for creative effects,
but if you want a driving kick and bass it’s best to keep the lowest frequencies mono.
Using a mid-side EQ, I can use a high-pass on the side image,
attenuating any bass on that image and ensuring the lows stay mono.
Modulated Distortion on Lows
With modulated distortion we can ensure that the distortion primarily occurs on a kick’s or
bass’s transients, in turn making the instrument cut through a mix. To do this I’ll use Saturn 2,
I’ll create a band, and create a envelope follower with a short attack, decay, and release.
On the second band I’ll heavily distort the signal and place its crossover
right above the lows. Then I’ll link my envelope follower to this crossover.
This way whenever the kick hits the envelope follower increases the value of the crossover,
meaning the lows become distorted as well, but in a program dependent way.