Hi guys Kirk here with kirk giordano plastering, today what I want to show you guys is doing a
pillar here this pillar is top of it yeah and I'm gonna flash I'm gonna counter flash the
flashing that they have here my son asked me a good question Dan's on that camera I put I was
gonna put this guy right here keep it flush with here and drop it down over this one it says what
yeah put it on the ground say like right here why do we gotta be at that certain area we're
gonna build this deck up they're gonna put a few membranes on here a waterproof membranes
they're not gonna concrete this if they were that'd be way up here they're just gonna put
membranes on this so this this counter flashing should go at least about say 2 inches above here
their membrane is only gonna be about 1/4 inch thick here so that going right there then this
one right here that gives me the foundation to start working my way up this post I'm gonna
go ahead and attach these guys let's say this one right here and I'm using the gun to attach
These are my tempers. Keep these
didn't have a saddle here saddles a piece of metal that goes over this and comes up the
wall because of the way this is working there's no living space under this however next thing
I'm gonna do is I'm gonna put this guy right in here working in the hot Sun so when you
when you're doing this peel and stick it really sticks to everything I'm gonna get this guy down
here right now rich how we do that we want a cook off paper in here however the paper
creates water joints in there we all know how water gets everywhere so what I'm gonna do I'm
gonna put this piece of membrane here then I'm gonna kind of pinch this this corner in with my
fingers like so I cut this one right here go over the drip screed and this goes over it it
kind of counters it then they're gonna play some flashing directly over this as well as
this flashing is gonna go down to here four inches you can go over the Southside what I
want to show you is water proof these guys right here I could use I give you as paper
but I prefer to use this peeling stick now the stick is kind of a drag to use it I'm used okay
a day like today you just touch it sticks to itself very well all right yep one side
and one side right where we wanted I could manage town dad it won't
stick to itself really if it sticks to itself
all right now that I got that thank you now you kind of make this joint right here use
your finger to crease it just like that and you kind of walk it through walk it through
markets or a sticker to the would make this a tight joint this way water can't penetrate
then we just hold this over like so I'm going to put a piece right here then I'll show you
how we wire these in place corners on another 20 minutes to get the rest of this in the corners
which are interesting okay guys remember this is always best to do early morning very hot I
got my one piece put the top down over here down on this side here and here so we are bulletproof
can't get any better than that now that we're bulletproof you are going to wire wire this to
this is kind of interesting because most flanges they like right here is three and a half inches
right here's a inch and a half we need to cut these and because they stick out so far we're
gonna improvise and cut them even more than the stock items all right guys now that we got
this membrane all done real nice fastened here tight all the corners are secure and tight no
water penetrating it our arch is nice then we go ahead and wire the corners which are
Four sides here plus the bottom, you're gonna take his snips. We're gonna hold back you're
gonna cut here then cut here let's cut it here that way this fastens inside we have this piece
here so far corner we'll tie everything in real tedious has got to take him 20 minutes to do this
all right Dan ask me is there a faster way to cut these no there's not it's a slow way I'm showing
him how to laughs he's showing me how to use this camera. Next, we're gonna put the corners
on because this fella put half-inch indentations on here or the surrounds. What I generally do
is I'll put my corners on first once I get my corners on that will allow me to gauge my next cut
these guns good stuff when they do we just pull out all right now now we're going with our half
flange again it has a full flange here and a half one these are designed for two by fours it won't
work for this because if I try to put it on here this one I'll show you okay see where this corner
is over this corner I put this one here now this one sticks out another inch further than this one
so we got the 20-minute project of cutting these individually we buy them stock like this thinking
that they'll make a big difference but build on only half inch you still have to improvise and
cut all of this off in 20 minutes I'll have all eight of these cut and we'll show you how that
goes on - all right guys just finishing up now and then these things are time consuming and I
spent about an hour and how I I even from here to here here here is what's this corner pieces
evened out exactly where I want it then I use it as my template or guy so I can just
put that one right there and I'm right at where I want to be stapled on I've already
our changes you can make are just big fits great for bigger trying to make small arches
it is a pain and a black take anyway what I did to cap this mess I have one gun except
for this one here I'll show you how I call I've been my arch it looks kind of ugly but
if I make it where it's not too pretty I can fix it with my cement I can I'm pretty good
with cement on luxury you're learning to do all this by mistake here you learn how
to do them well especially if you have to redo one or two so anyway it's all true and plumb
level both sides of trim, anyhow my name is Kirk I'm with kirk giordano plastering,
thank you, folks, for watching, and as usual we'll see you at the next one