try to go to the side pull one side out like that support it support it
pull it off and you go to the middle
there you go guys
hey guys welcome from red models so today we're going to be doing a removal
of a 20 20 dodge charger front bumper if you guys like this video go ahead and like subscribe and
turn on that push notification and if you need any pre-paint auto body parts or in particular
this bumper for your vehicle go to revemoto.com your pre-paint auto body power source and the
link is up above and also down below let's go ahead and get started on this vehicle
all right we're gonna work our way to the bottom first so right there in the
bottom you're gonna get a seven millimeter socket it's gonna be something like this
you're gonna have i believe a couple of bolts down there not a couple of like around two four six i'm
gonna guesstimate eight so all right so it's a little bit of awkward position right here but
it is right underneath the bumper right here so it's gonna be one two three four five six
six little tiny bolts so let's go ahead and take that off
all right guys so once you get to get those bolts on the bottom off you're gonna come to the side
of the bumper you're going to see these push pins right here so you can take them off with
a fly head or a panel removal tool that i have so let me show you guys what that looks like
so if you guys are fortunate enough to have one of these paddle removal
tool sets you guys can go ahead and use that to take this off a little bit easier
but if not a fly head will work also so let me show you guys how a flathead would work
just insert it in there and kind of twist it just gonna go around that uh the push pin
all right so nothing looks like that all right it's easier with one of these things because
it kind of acts like two fly heads and then just
insert it in there as you guys can see just pulls out the whole push pin up
so there's gonna be one two
three of them
so you're gonna go and do that on the other side also let me just push this to the side all
right guys so you guys can see the wheels already turned let's see if i can actually pull this back
so i gotta take off these clips so it's kind of a couple clips right here
i try to do it so i don't like block you guys from seeing what i'm doing but basically i had
to kind of look underneath there again these push pins gotta go there's one like right here
there's another one right here right next next to the fender
so these two gotta go because that way i can kind of maneuver the fender liner
just push this back a little bit
then get your 10 millimeter work your way up there
so again it's just like it's not even tight at all i don't know if it's meant
to be like that or someone worked in this car but it's not tight at all
right here so you guys can see i'm not even using a soccer wrench i'm just using my
hand to twist it with that socket and it's just coming right off
there it is so now i'm going to work my way up to the next one which is right
right here so again i'm just twisting it
literally i'm just twisting on my fingers what the hell with that socket but that's about it
there it is last one right there so
all right so if you guys look around there's gonna be pushpins over here on the side
let me show you guys right there one start off right there and just work
your way around so it's gonna be one two three four five six
all right flat head or one of these panel removal tools
hopefully this one's a lot easier man that kind of winded me out on that one side of the fender
all right these are a lot easier are you trying to take this cover off
it's so much easier if you guys have one of these tools but a fly head also let me let
me demonstrate what a flathead would look like shouldn't be that hard either with a fly head
so all you do is insert in there yeah just lift up it's like opening up uh here in texas
or louisiana it's like opening up clamps or no not clams oysters like a chuck shucker chopper
all right so that's going to be 12. i'm going to pull up on this
so let's see if the bumper can just gonna go ahead and come off now
all right guys so that's why you don't you resist the urge just to pull the bumper if
it's really tight right here is another 10 millimeter bolt so you guys can see
so go ahead and get a 10 millimeter
all right here it is
all right i did a little bit of investigation because from what it shows that it should just
come right off but it looks like on this particular model there's like an air dam
like an air inlet down there and it's connected by these bolts right here in
the back so one two three of them i think we gotta take those off
right there so you guys can see the air dam right there and there's gonna be three bolts
around that there there it's like an air inlet so it's like a seven again
all right so here's a little better view i took off the other one because the bolt
was stripped but on the other side so let's see back view right there
all right so here's your bumper
the bumper comes with this air dam right here in the bumper lower bumper you go right behind that
where the fender liner is right in front of this tire there
are three screws right there and there's gonna be seven millimeters as you guys can see right there
i'm gonna have to take those off all right let's try this again so apparently you can just hold it
oh discover this right here
just snapped off so just come down there so it's okay it's not broken or anything
so there's a wire right here
here
well it is this bumper right here down by these uh tabs so all i'm doing is pulling the tabs off
like that so that i'm gonna bring you guys to this side right here we're gonna unhook this clip
yeah so that's the light so let me show you guys so if you guys come right here on the side
i can right there there's a wire this wire right here basically just unclip it
it's just a uh it's for the reflector
so let me put you guys down because it's hard to take off with the camera being held
so there's a clip right here if you get a head you gotta
pull push up on this tab and it'll release this so let's do it on the other side too
all right so finally got this bumper off so let me just recap
it because this car deserves a recap first down here this can be those seven millimeter bolts
take those off there's around six of them two four six of them then we went to the side
remember there's gonna be push pins right here take those off then up here
there's gonna be two more take those off you're gonna push the fender liner back okay
you're gonna take off those bolts and be two of those remember they're really long look like this
you can actually remove them with your hands with a 10 millimeter socket
then once you just once once you do those on both sides you're gonna come back here there's going
to be a seven millimeter bolt holding the air dam that's a cooling system for your brakes i believe
take those off there's gonna be three of those once you take those off on both sides
you're gonna come up on top there's gonna be a push pins one two twelve of them let's
follow those before you take off the bumper take this charger cover off just like that
all right all right once what i just recap is done go to the middle twice look inside
pull one side out like that support it support it support it pull it off and go to the middle
there you go guys
all right that's how you take off a 2020 dodge charger front bumper guys i do want to thank
you again for watching our great videos if you guys need any parts for your vehicle the ones
that you guys see in our videos or anything else we go to revemoto.com your pre-painted auto body
part source we sell bumpers tail lights headlights uh touch-up bottles everything that you need for
your vehicle go to revemoto.com your pre-painted and accessories parts store also go ahead and like
subscribe and turn on your push notification for more great videos like this one thank you