hey guys welcome back to the channel So today we're going to be installing
these new fog lights these are four in one fog lights from WS headlight and they sent these
to me to test out on my sienna if you didn't know Toyota and Lexus use a very common and
interchangeable fog light since about 2009 2010 so these bolt into all the different
cars so my CNN already has led fog lights from Morimoto I swapped those out back when
I bought the car brand new but I like these new ones because they're supposedly a four
in one so they have a DRL they have a fog light they have a turn signal and they have
one other thing which I don't know so we'll go figure out what's on here so stay tuned
thank you
so these fog lights just looking at them they're pretty nice or very well designed with a nice heat
sink it's got the logo the Ws logo right etched into the lens and everything looks pretty good
from what I've seen compared to other LED fog lights both OEM and aftermarket that I've seen
they've got the adjuster screw on the back for height adjustment which is a plus you don't see
this very often anymore with these type of fog lights right here so I opted to get the yellow
ones for the install today so we're going to be putting these yellow ones in they're going to
give it like a nice JDM yellow so on here on the instructions it comes with a pretty nice
instruction set it basically tells you how you wire up everything and it's pretty much plug and
play all you need to do is plug in the fog light right here run one wire for your actual power for
your DRL and then a parking light wire if you want the side light that's the fourth function right
there it has a parking light that you can actually use which is essentially a daytime running light
in order to run these it actually runs its own separate power supply or controller so
I can actually do the drls and just looking at all the wiring and everything these are actually
OEM plugs right here that are used on Toyota so that's a pretty high quality item right there
this thing comes with everything you need to install it actually even comes with a add a few
so you can add it and there's two types to add a fuse for the different fuse blocks you have the
actual sticking out pin ones and the flush pin ones that I thought of everything on here they
even have the 3M tape to stick your controller underneath your bumper or wherever you end up
mounting that thing so in order to install these we have to actually remove the bumper if you guys
don't know how to remove the bumper I think I have a separate video where I've removed this
bumper before but it's pretty straightforward we just need to take apart all the clips up top
the two screws and the clip on the side and the fenders and then all the 10 millimeters
at the bottom and we just pop this thing off on the sides and it comes right off along with the
Grille once you take it off you could make sure you unplug your fog lights and everything take
the whole bumper off and then you can install the new fog lights and do all your wiring underneath
the bumper off as you can see the fog light is accessed through the back here so all Toyota fog
lights have four mounting spots most of the time they only use two or even one screw on
here you can see two of the tabs go into here and one screw holds it and this one doesn't do
anything so that's pretty much how they mount these things on the Sienna on other cars I've
seen it's just kind of random on what they choose to mount it with so we'll go ahead
and take these off Mount the new ones in and then we've got to do the wiring on the car
all right right here we got the Mori motor one I've been using since I got this car new when I
bought it like a month after I got the car and these things you can see they're pretty pitted
now and used up they have that same projector that these new ones have right there like little half
LED projector you can see the build quality is pretty good on the morimoto's with the heatsink
there and the adjustment screw very similar to what we have now this one's a little bit more
flat but versus the curvature on here but on the actual bumper you won't even notice it anyways
all right so here we got it on the car right now the fitment's a little bit whack as far as the
lens goes the Morimoto is a bit rounder like more like the OEM where it actually filled in the Gap
more with this you can actually see right through here you can actually see the mounting through the
clear and then you can see the mounting over here which is kind of whack but with these and
the DRL being on during the day all the time it might hide a lot of that but when you see
it without the lights on you're gonna see these gaps right here which kind of sucks all right the
next thing I need to do is run the harness for the drls in the parking lights so we basically
have one way to put it on the short side and the long side you want to use the long leg of the Y
over through that side you want to keep this over here near the fuse block because this is on the
driver's side tap the fuse block with the green right there with that fuse then the blue down
here goes to the parking light so I'll just tap a parking light over here on this headlight and
we're going to go ahead and mount these things over here I'm just going to mount it right to
this reinforcement it right here I'm going to use the tape to tape it but I'm also going to drill
a hole just to make sure it doesn't fall off so this is the input from the fog light signal from
the car and then the DRL that we're going to run over here and then we're going to run the yellow
wire to the turn signal on each side so down here we got this big old jumbo mess of wires as you can
see and the easiest way to figure things out is just to find out and know what your wires are so
the turn signal is like in this bundle right here so you just gotta look behind the headlight and
see what color your turn signal is find the wire right here and tap it and then the parking light
is right here on this one that goes to the corner light so that's the parking light so I'll just get
the wire that comes out of here and then I'll tap it right there I'm going to heat shrink and solder
just because I like all my stuff clean so over here on the passenger side you can see the turn
signal right there harness it's got the white and black wire which is the ground and then I think
it's a brown wire on this side is the signal so on this side I actually dropped the harness for
the signal and my DRL is the factory DRL on my 2015 SE this thing's actually got everything I
need to make the connections if I wanted to right here and I just might do that without running the
power into the actual car I might actually do that so I don't have to run power straight to
the fuse box I'll just Jack the DRL right here I'll test that first to make sure it works and
then over here is a turn signal so you can see the yellow right here is the same yellow that
goes into there and then over here is my parking light which is a green wire for the parking light
and this actually goes into here also so it makes it pretty convenient just because the
drls take all these signals and the reason why they take a turn signal in here is actually a
Switchback already designed into this DRL during the day when you signal this thing turns off
foreign
so I plugged this thing up just to test it I haven't made any final connections yet but
it looks like the turn signals are working I'll go ahead and check the fog light DRL
and parking light now so right now we got the fog light on we got the parking light plugged
in if I unplug the parking light let me see what happens right this thing is but I think
this thing might only I think the parking lot I was able to test everything and I kind of
figured everything out right now the blue wire on here is a dimming wire and it only dims the
DRL when the DRL is on so when you have your parking lights or your headlights on this thing
won't be full brightness at night it'll just dim down the DRL so we wouldn't need to make
that connection my idea of using the DRL signal out of here doesn't work because the OEM One uses
a grounded output so we'll go ahead and have to run that to the fuse block using the add a fuse
foreign
I was able to heat shrink the signal and the parking light to my harness
here so I'm gonna tie all this back up with some 3M electrical tape get all
the loom back together and just tape this all nice and OEM looking again
all right so pretty much got everything buttoned up over here put all these tie wraps electrical
tape made everything look pretty across the front here all the way over this side and I
went ahead and finished the wiring of the one turn signal over here up to the thing with our
new wire loom so I mounted it underneath here with the tape and the screw we got it all nice
and pretty looking the next thing I gotta do is fish this wire up into here through this little
hole with all the wires coming in and I'm going to get the EFI the electric fuel injection fuse as
my add-on all right I was able to fish this green wire right up this little sleeve right here there
was a little crack in there with some light I just looped it around pulled it through and I got it up
through here I had to unplug these harnesses right here just to kind of access it and see
it better but now I'm in there I can pull it up and it'll be a nice clean install got everything
soldered nice and neatly I checked all the fuses down here and everything under here is actually
powered constantly on this side the only fuse I found was this 10 right here which corresponds to
EFI number two that's the only one that doesn't come on unless the car is on so that's what I'm
gonna be using right here for the DRL plugged it up right there onto that fuse like I said
are you alive
always breathing that's the red lights driving at night wait till this ride feeling alive nothing
in sight forever in Flight follow those times we'll make it this time blurry tree lights hey
guys thanks for watching all the way to the end of this video on doing those four in one fog light
upgrade on my sienna there is a lot of wiring involved in this especially if you want to do
it right and clean if you want to do it really easy and painless you could just use the quick
clips and it'll take you like five ten minutes to do all that wiring for all you guys that follow me
and stay to the end of this video I'm going to give you a chance to win these same fog lights
I've got an extra set of these actually I've got two extra sets of these uh in white so if
you guys want a chance at winning this just leave a comment down in this video remember
these things will fit a bunch of different Lexus vehicles and Toyota vehicles from the
last 10 or 12 years it should fit your car if you have regular round Toyota fog lights
all you have to do is like this video and leave a comment at the end and I'll select a winner
in the next few weeks remember guys for all these different DIYs private whether it's on
the Sienna on the is-300 on the is-250 around the house or whatever I'm doing if I can do
it you guys can do it I want to thank you for watching and I'll talk to you guys next time