1. Take out the device and accessories. 2. Hydro dermabrasion handpiece is connected
with the main machine. 3. You'll find hydro tips and rubber ring
inside the accessories bag. Detach the tip before you replace any faulty rubber ring.
4. Attach the hydro tip onto the handpiece. 5. Replace any faulty fuse with one of the
two spare fuses. Pry open the fuse cover with the screwdriver, take out the faulty fuse
and replace it with the spare fuse. 6. Take out the screws and start to install
them. Aim the handle holder at the right place and twist the screws into the machine.
7. Connect LED photon mask handle with the device
8. Connect ultrasonic handle with the device 9. Connect cold hammer handle with the device
10. Connect RF handle with the device 11. Connect BIO microcurrent handle with the
device 12. Connect the hydro spray handle with the
device. Tighten the screw. Connect the hydro bottle with the handle and tighten the screw.
Connect the hydro spray with the other end of the handle and tighten the screw.
13. Place the handles onto the candle holder 14. Connect with power supply.
15. Check if everything's properly installed. 16. Fill the bottles with a solution.
17. The two bottles are clean bottles and waste bottles. The clean bottle is filled
with a hydro dermabrasion solution. 18. AS1 can be used for deep cleaning and
is suitable for oily skin, coarse skin, and congested skin.
SA2 can be used for deep cleaning and is suitable for all skin types.
AO3 is suitable for sensitive skin. Normal saline can be used to clean the tube
and is suitable for sensitive skin. 19. Twist open the clean bottle cover and
pour in solution. Note: There are two clean bottles and they
are interlinked. When you pour the solution into one bottle, two bottles are filled with
the same solution. Pour in one solution only each time.
20. Click the power button to turn on the machine.
21. The default interface is hydro dermabrasion function when you turn on the device.
22. Adjust working time between 0-60 min. It is advised to treat 10 min or so.
Note: Energy levels of hydro dermabrasion and hydro spray are not adjustable.
23. There are altogether 8 hydro dermabrasion tips to choose from based on different treatment
sites. 24. Click to start.
25. During hydro dermabrasion treatment, solution transfers to the skin and then to the waste
bottle as wastewater. When the waste bottle is full, the device will stop automatically.
So empty the waste bottle in time. 26. Twist the hydro dermabrasion knob to adjust
the suction level. 27. After the treatment, empty the waste bottle.
Turn on the red valve to pass out the wastewater. 28. Fill in the clean water bottle with normal
saline after each treatment. Turn on the device and stop the handle with the thumb so the
saline can circulate and clean the device. 29. Soak the tips at 75-degree alcohol to
disinfect after each hydro dermabrasion treatment. 30. Click hydro spray jet on the screen. Adjust
working time. It is advised to treat each treatment site for 10 min or so.
31. Take out the hydro spray jet. Fill in the hydro bottle with water. (Choose from
purified water, watery essence, toner, normal saline, etc., based on skin needs.)
Twist the bottle back onto the handle and tighten the screw.
32. Click start. Twist the end of the hydro spray jet to adjust the level of mist. Press
down on the wrench to spray.
33. Click ultrasound on the screen. Adjust the energy level. The energy level ranges
from 0-10. It is advised to adjust between 2-8. Working time ranges from 0-60. It is
advised to treat each site for 15 min or so. Click start. The probe emits a blue LED. Apply
essence before treatment to better lead in nutrients and help skin absorb better.
34. Click RF on the screen. Adjust the energy level. It is advised to adjust between 3-8.
It is advised to treat each site for 15 min or so. Click start. The probe emits a red
LED. Apply essence before treatment to tighten skin and increase skin elasticity.
35. Click a cold hammer on the screen. Adjust the energy level. It is advised to adjust
between 5-10. It is advised to treat each site for 10 min or so. Click start. Apply
essence before treatment to shrink pore and calm skin.
36. Click the BIO microcurrent on the screen. Adjust the energy level. It is advised to
adjust between 2-6. It is advised to treat each site for 10 min or so. Click start. The
probe emits a green LED. Apply essence before treatment to tighten skin, activate skin cells,
and brighten skin. 37. Click the LED photon mask on the screen.
Select color. There are 7 different lights of LED. All target different skin issues.
Select the LED-based on one's own skin needs. Select mode. There's mono-color consecutive
mode, 7-color cycle mode. Mono color consecutive mode targets specific
skin issues. 7-color cycle mode can be used to improve
skin texture, soothe skin, and help skin absorb batter.