Welcome to the Matrice 350 RTK (M350 for short) tutorial video
This video will show you how to use your M350 for first flight
Open the carrying case
Insert the landing gear to the connector on the aircraft
slide and rotate the gear lock clockwise to the locked position
Take out the aircraft from the carrying case
Unfold the frame arms
Rotate the frame arms to the locked position
Slide and rotate the arm lock clockwise to the locked position
and make sure that the frame arms are mounted firmly
Unfold the propellers
Install the gimbal and camera (Taking Zenmuse H20T as an example)
Align the white dot on the gimbal with the red dot on the gimbal connector
Rotate the gimbal lock to the locked position
Remove the camera cap
Take out the batteries
Install the batteries
Rotate the battery release toggle by 90° and make sure it clicks into place
Activating the Remote Controller Battery
The remote controller is in hibernation mode before delivery
Before the use
connect the remote controller and battery station
with the USB-C to USB-C cable
and charge the remote controller to awaken it
Press
and then press again and hold the power button for three seconds
to power on the remote controller
Follow the on-screen prompts to activate the remote controller
Device Activation
Press the power button once
then press and hold the button again in 3 seconds
to power on the remote controller and the aircraft
and enter the DJI Pilot 2 app
Then the activation page will pop up automatically on the app
Read related terms
Authorize the use of device information
Select a usage scenario for the device
Confirm the account activation information
Tap “Activate”
Tap “Restart Now” to complete the activation
First Flight
Run DJI Pilot 2 app and tap “Enter Camera View”
Complete the preflight checklist as prompted on the app
Remote Controller
Unfold the antenna of the remote controller
and adjust its position to ensure the aircraft
is always in the optimal communication range
Takeoff and Landing
Maintain a safe distance of at least 5 meters from the aircraft
and operate the aircraft by facing its rear
Start the motors by pushing left and right control sticks
to the inner or outer bottom corners
When the propellers are spinning
gently push the throttle stick to take off manually
The left control stick is used for adjusting the flight altitude
and nose direction
The right stick controls the forward
backward
leftward and rightward flights
On the video transmission screen
you can see the current flight distance
altitude
speed and other parameters
Functional Description
Tap the Shutter/Record button to switch between photo taking
and video recording modes
Tap the Playback button to view and download photos or videos
Use the left and right dials of the remote controller
to adjust the pitch and yaw angles of the gimbal
Tap L1, L2 to quickly switch among three cameras
infrared
wide angle
and zoom
Tap R1, R2 to zoom in and out the zoom camera
Double tap the target point
to make the gimbal and camera quickly align with the target
Tap the laser ranging icon to enable the laser ranging function
Align the cross cursor with the measured target
At this time
RNG indicates the relative distance between the target and the aircraft
while ASL indicates the altitude of the target
In the infrared mode
use the Spot Meter function to tap and measure the temperature
at any spot on the screen
Use the Area Measurement function to select the area of interest
and move it freely
The highest and lowest temperatures of the area
will be displayed on the screen
In addition
you can set the high temperature alarm function as needed
Tap the Palette & Isotherm icon
Adjust the palette based on scenario needs
The flight pause button can pause the aircraft
in any flight condition
making it hover in the air
Press and hold the RTH button of the remote controller
to start a Smart RTH
Hot Battery Replacement
The battery hot replacement is available for the M350
Battery replacement can be done without powering off the aircraft
improving the replacement efficiency
Unlock the battery release toggle
remove the battery on one side
and replace with a backup battery
If the battery indicator lights up
it suggests that this battery is installed in place
and the battery on the other side can be replaced
Power off and Storage
Press the power button
then press again and hold
to power off the aircraft
Rotate the battery release toggle by 90°
and remove the batteries
Press and hold the gimbal detachment button
rotate the gimbal lock to the unlocked position
and remove the gimbal and camera
Rotate the gimbal axis arm to align with DJI logo
and rotate the lens to be perpendicular to the gimbal axis arm
Insert the gimbal camera to the case
Rotate the arm lock counterclockwise to the unlocked position
Slide the arm lock from the bottom of the connector
Fold the rear arms
Fold the front arms
Place the aircraft upside down
and put it into the carrying case
and make sure that all parts are placed inside the slots
Rotate the gear lock counterclockwise to the unlocked position
and slide the gear lock from the bottom of the connector
Remove the landing gears and place them to the carrying case
Press the remote controller power button once
and then again and hold to power off the remote controller
Fold the antennas
Place the remote controller into the carrying case
Fold the propellers inward and parallel to the aircraft body
to prevent potential damage to the propellers caused by pressure
from the upper foam inserts of the case
Close and fasten the carrying case
Thank you for watching!