- Hey, what's up guys?
Welcome back to The Chemical Guys Detail Garage.
Today, we have a 2013 Aston Martin in the shop
and we'll be treating it, to a foam wash,
using the Big Mouth Max Release Foam Cannon,
with Black Light auto wash and Clean Slate.
Let's get started.
You guys might say,
Henry, the Aston Martin is in perfect condition.
That is because it is in the shaded area.
Once it pulled up, we noticed this car has everything on it,
such as clay marring, polishing marring,
pigtails, tiger stripes.
The paint is not in the best condition.
It is a three-stage paint.
So it has a lot of high gloss and shine
and a lot of reflection.
But, unfortunately, the owner does not care for it.
It sits by the beach a lot.
And keep in mind there's dirt, and salt that lands on it.
Within a week, and over time,
it just diminishes the look of the vehicle,
and as well as the clear coat.
So today we're going to start off with step number one,
which is going to be a wash.
Because we're going to strip off everything off of this car,
such as the glaze, the seal and ceramics, waxes.
So whenever we come back
and apply Carbon Force ceramic coating, it bonds properly.
But now it is time to start off with the foam wash.
So right here, I have my Big Mouth Max Release Foam Cannon,
with Black Light and Clean Slate.
So Black Light does not strip off anything
because it is a PH balanced soap.
But, Clean Slate on the other hand,
will remove any glazes, sealants or waxes
that are sitting on the surface of vehicle.
So I will remove the top off of the Big Mouth.
If you're not familiar with the Big Mouth,
the Big Mouth has a two-inch diameter head
that is going to produce tons of suds.
Whether you have a small vehicle or a large truck,
it's going to lather the surface of your vehicle
with thick amazing suds
with just the use of using a pressure washer,
and your Big Mouth Max Release Foam Cannon.
So I'll put the head to the side.
I will open up my Black Light auto wash.
And I will be applying two ounces
into my Big Mouth Max Release Foam Cannon's canister.
As well, I will be applying Clean Slate to it.
So if I use Clean Slate by itself,
unfortunately it will not foam up,
but it will still strip off.
But I still want to give you guys the thick lather effect
whenever using the Big Mouth Max Release Foam Cannon,
so this is why I'm mixing the soap.
And that is correct,
you could mix Clean Slate, with another soap,
as long as it's a pH balance soap.
Do not use Clean Slate
and Citric Wash and Gloss,
because Citric Wash and Gloss
is a soap that is highly concentrated,
and that will also strip off everything.
So let me just twist on the head back onto the Big Mouth.
And now I will stir it and not shake it.
So I get the proper mixture and I do not get any foam
inside my Big Mouth Max Release Foam Cannon.
So my Big Mouth is ready to go.
Now it's time to set up my two buckets.
So on top of here, I have my dirt traps.
My dirt traps are going to help me filter while I wash.
The dirt traps are two different colors.
We offer four different colors,
where there's blue, green, black, or even red.
But I like using two different colored dirt traps,
so I know exactly which one's going into my wash bucket,
and which is going to be in our rinse bucket.
So I will insert them at a 45 degree angle.
So on my right-hand side,
the black dirt trap is going to be my soapy bucket.
And on my left hand side, my red dirt trap,
is going to be my rinse bucket.
So we always recommend doing a two bucket method,
whenever you're washing your vehicle,
whether it's a Camry all
the way to the Aston Martin and Lamborghini.
You always need to do a two bucket method like this.
You avoid scratches and swirls and improper washing.
So, same exact thing.
I will be adding one ounce, of Black Light into my bucket,
as well as Clean Slate.
Like this I get the proper mixture,
and same lubrication whenever I use
my wash mitt to dunk it in.
And the wash mitt I'll be using today is going to be
The Stranger Helpful Handy Mitt.
This is going to allow me to get into your intricate
details, especially cause this car has amazing body lines.
So I'm going to get into a hard
to reach areas using The Stranger.
But now, enough talking, it's time to activate the suds
and foam this Aston Martin using
the Big Mouth Max Release Foam Cannon,
with Black Light and Clean Slate.
Let's get started.
Alright guys, so I just finished
foaming up the Aston Martin.
I let the suds dwell on the surface,
just so it could remove any dirt or grime that it might be
still on the surface of the vehicle,
but now it is time to scrub it down,
using The Stranger Helpful Handy Mitt.
I'll go to my soapy bucket.
I'll get tons of suds.
Now I'll go to the highest point of the vehicle,
and I'll scrub away in linear motions.
By me scrubbing in a linear motion,
it's going to help me remove dirt and grime properly,
without scratching the surface of the vehicle.
After a couple passes,
you'll go to your rinse bucket, with the clean water,
and you'll scrub it at the bottom just so you make sure
everything is removed from the mitt.
But guys, now it's time for
me to finish scrubbing out the vehicle.
Then I'll meet you guys inside the bay, where we're going to
clay the surface to get it ready for polish.
I'll see you guys then.
Alright guys, so we just brought the car
into the detailing bay
and now it is time to clay, the surface.
You always want to clay the
surface to remove any contamination,
off the paint because like this,
you're going to get a better bond from your ceramic
and it's going to look a lot better
and you're not going to seal
any contamination under the ceramic.
So today I will be using the clay block.
The clay block has a full synthetic side of pure clay.
And my lubricant I'll be using today,
is going to be Clay Luber.
So Clay Luber is a synthetic lubricant,
that's going to help me glide my clay bar, or block across
the surface without damaging the surface,
or causing clay marring.
So I already sprayed some Clay Luber onto the surface.
I'll spray some Clay Luber onto my block
and I'll just rub it side-to-side.
So what clay block is going to do,
it's going to remove any contamination,
that is sitting on the surface of the paint.
You never want to seal contamination, under,
whenever you're applying a ceramic ,or polishing,
because keep this in mind,
if you are going to polish with
contamination sitting on the surface of your paint,
you're going to be pushing all that
contamination deeper into the paint,
which can potentially cause more scratches and swirls.
And you're going to have a little bit
more hard time whenever you're polishing.
So all you need to do is just spray it and glide it across.
So let me just finish claying the whole entire car
and I'll show you guys the finished results.
And guys, if you guys like this video today,
don't forget to give it a huge thumbs up,
comment down below on future videos you wanna see.
And make sure to stay tuned on part two,
where Joey polish out the surface,
and then he applies Carbon Force ceramic coating.
We'll see you guys next time.