Hi, DIYers.
Joe from AlarmGrid here.
And today, we're going to talk about had a how to add a 5,800
RP to a LYNX Touch panel.
Now, a 5,800 RP doesn't have to be programmed in for it
to work.
As soon as you plug it in, it's going
to start providing that repeating function.
And what that does is actually repeat any 345 megahertz signal
that it hears, so you get an extended range on your sensors.
If you do want to program it into the panel, what that'll
do for you is that when a trouble condition occurs
on the 5800 RP, it's going to show up on your panel.
Now, there's two different ways to program it in.
You can have it occupy one zone in programming.
And if you do this, all the trouble conditions
will come in on that one zone, or you
can break it off and have four different zones programmed
for it, for all of its trouble conditions.
That's the recommended way to do it,
because it's going to give you much more detailed information
about what's wrong with the 5800 RP.
If you do program that in using one zone,
all of the trouble conditions will come under that one zone.
And what you're going to see is that if there
is a AC loss or an RF jam, it's still
going to show up as a low battery check-in on the system,
but it won't trigger an alarm, just in case the system
is armed when this occurs.
Again, the recommended way to do this, though,
is to break them all off in individual zones, which
is what we're going to show you how to do today.
Again, when we do program it in, you're
going to see what it looks like when we do program it in as one
zone.
And then we're going to have to do something on the 5800 RP
to access the second serial number on the unit
to get the other zones in.
But let's take a look at the 5800 RP,
and let's get in the zone programming on our LYNX touch,
and then we'll take it from there.
So we have our 5800 RP open.
And as you can see, the serial number
is printed right here on the board.
Now if you're just going to use the one zone for trouble
reporting, all you're going to have
to do is program in this serial number to the system
and name it appropriately.
What you're also going to see us do later
is we're going to move dip switch number two.
If you're just using the one serial number,
or if you're programming it in, or starting to program in
all your trouble zones, you're going
to want that dip switch two to be off.
So as you can see, it is off right now.
So let's go over to our LYNX touch
and get into zone programming.
So on the LYNX touch, let's go to Tools.
Enter the Installer code, 4112, program, and then Zones.
Let's go down so we get a whole new fresh set of zones.
I'm going to click zone number seven and click Edit.
Now, like any other sensor, to learn this,
we're going to click on serial number,
and now the system is in learning mode.
So heading back over to a 5800 RP.
I'm going to click the Tamper switch,
and then I'm going to release it.
I got one beep.
I'm going to do it again.
[BEEPING]
I got two beeps, and you can see the serial number has shown up
on the system.
I'm going to do it a third time.
[BEEPING]
And we get three beeps, and it is learned in.
Now if we were to just use this one zone for all of our trouble
reporting, this is all the programming
that we would have to do.
And what we're going to do is set it to--
we're going to name it first, so we know what it is.
And we're going to do low bat--
ZZTV.
Check in.
5800 RP.
Done.
It's going to be loop number one.
Device type, we're going to set to Other.
And then for the response type, we're
going to set this to 24 hour auxiliary.
Supervision is going to be supervised.
Alarm report.
We're probably going to want that on, and we're all set.
So we click Save.
And now, we have the 5800 RP programmed in
to work on that one zone.
So again, if we just left it like this,
if there was an AC loss or an RF jam,
those would show up with zone number seven, with this info,
but it wouldn't set the system off if it was armed into alarm.
But we want to have more detailed information when there
is a trouble on our 5,800 RP.
So what we're going to do is head back over to our 800 RP.
We're going to set dip switch number two to On.
What this does is it switches it to the second serial number,
which is the existing serial number plus one.
So it's going to be 0750154 now.
This is going to give us those three
additional zones to program in the other trouble conditions.
So back on our LYNX touch, we're going to select a new zone.
Click Edit.
Just like before, going to click serial number to put
the system into Learn mode.
And then back on our 5800 RP, we're
going to click the tamper switch, just like before.
So I'm going to click it.
I go.
Click it again.
Let go.
As you can see, that is the serial number that we want.
It's the serial number that's on the board, plus one.
I'm going to click it again.
And let go.
Now, as this is the first zone of the new zones,
or the second set of zones for our trouble conditions,
this is actually going to work as our tamper trouble.
So what I'm going to do is enter Tamper.
T.
[BEEPING]
5800 RP.
Device type, I'm going to set this to Other.
The response type, I'm going to Day/ Night.
What this is is troubled by day and alarm by night.
This means that if the system is disarmed,
it's going to create a trouble.
If the system is armed, it will go into alarm.
An important thing that we do have to do
is set the supervision on this to unsupervised.
In these three zones from the second serial number,
they're all going to be set to unsupervised,
and it's important that you do set that as that, or else
you're going to get some weird conditions,
and it's going to be very frustrating.
So now, I'm going to click on Save
to confirm our programming.
And we're to do the next to trouble zones.
So going to click on the next open zone, click Edit.
Click on serial number to put it into a learn mode.
And then back on our 5800 RP, I'm gonna do the same thing.
Click the tamper.
Let it go.
One beep.
Click the tamper.
Let it go.
We've got two beeps.
Click the tamper.
Let it go.
We got three beeps.
So now, we're working with the second trouble
zone of this set of zones that I'm programming.
We go to our LYNX Touch.
What we're going to do is we're going
to set loop number to number 2.
And this is actually going to work as our AC loss zone.
So I'm going to do AC.
I'll put it all in this loss.
5800 RP.
Device type, we're going to set this to Other.
The response type, we're actually
going to do 24 hour auxiliary.
And again, we're going to want to make sure
that we set the supervision to unsupervised.
So now that we have that locked in, we're going to click Save,
and then we're going to program in our last trouble zone.
So I'm going to click the Next open zone.
Click on Edit.
Serial number to load up the Learn mode.
And then again, on our 1500 RP, I'm going to click the tamper.
Let it go.
Click the tamper again.
Let it go.
Click the Tamper one more time, and let it go.
Now we have our third trouble zone
of the second set program done.
So our loop number for this one is
going to be a loop number three, and then the zone description
is going to be RF Jam.
So FR Jam, 5800 RP.
Again, our device type is going to be Other.
And then the response type for this one,
again, is going to be 24 hour auxiliary.
And again, we're going to want to set our supervision
to unsupervised.
Go ahead and click Save.
And now, as you can see, all the trouble conditions
that could occur on the 5800 RP will show up
as their own individual zones, which
will make it much easier to troubleshoot
if anything happens to it.
Before you do back out of programming, though,
I do recommend that you clip the cover back on the 5800 RP.
Because that will give you an immediate trouble if the tamper
isn't pushed in.
All you have to do to do this is hook it into the back plate,
swing it down, and close it.
Now in programming, click the back arrow.
Click the back arrow.
You always want to say yes to allow installer
to re-enter programming.
Click the back arrow.
And we're all set.
We're getting a system trouble because of the low battery.
But as you can see, nothing on the 5800 RP
is popping up, telling us that we're good to go.
That's how to add a 5800 to a LYNX Touch panel.
If you have any questions about this process,
the 5800 RP, or the panel itself,
feel free to head over to our website, www.AlarmGrid.com.
Send us an email to support@alarmgrid.com,
or give us a call at 888-818-7728.
If you did enjoy the video, feel free to subscribe.
But if you want to be notified when we post future videos,
hit the notification button below,
and we'll send you an update when we do so.
Thanks for watching and have a great day.