Hi, DIYers, Joe from Alarm Grid.
And today, we're going to be installing a Honeywell 6290W
touchscreen keypad, one of these guys
right here, to our Honeywell 128.
We're going to do this all the way
from the beginning of wiring to programming the keypad.
So the first thing we have to do is wire it up.
So right here, I've already cut my hole in the sheetrock,
and I've put the back plate on the wall.
But you are going to want to do this if you are installing
this device on the wall.
I put three screws in my back plate.
I leveled it.
It's nice and secure and ready for the keypad to be mounted.
I've also taken a four wire conductor, or four conductor
wire, and passed it through the hole in the back plate,
and I also have it coming out through the hole behind my 128
VISTA panel.
Now, I've already stripped my wire tips,
and I'm ready to install them on the terminals.
I've 100% powered down my VISTA-128
I've unplugged the power, and I undid the battery.
I undid the red part, but I'm going
to do the black leads too, just have totally disconnected.
We are totally powered down.
Before you install anything, especially a keypad,
you want to make sure to turn off your panel.
Now the 128 VISTA, the four wires
that you're going to connect the keypad to, or the four
terminals, it's a little different than a VISTA-P panel.
So if you're used to working on, like, a VISTA-15P or a 20P,
and you're moving up to a 128, make
sure that you have your instruction manual in front
of you, and that you know where you're laying these wires,
because some of this stuff does change.
If we take a look, you'll notice that terminal number six
is our positive for power.
Terminal number seven is our negative for power.
Terminal number eight is our green data.
Terminal number nine is our yellow data.
What I'm going to do is loosen up these terminals,
make room under these clamps, and then insert my new wires up
under each terminal, and then tighten down
to make sure the connection is good.
So pardon me if I get in the way of the camera.
I'm going to try to orient myself
so you can see what's going on, but I may be clumsy too much.
If you have some extra space on one side of the terminal,
you can slip the wire underneath there,
so that the clamp gets a nice even squash on top of them,
a nice even press.
Now, on this one, this black wire
is kind of moving all over, so I'm going to take my time
and pull it out.
I'm going to straighten the tip out and then reinsert.
And as I was doing that, I actually pulled this one out,
which shows me that I have to make this connection
a little more secure.
And you're going to notice this when you go to wire,
it's not going to be as easy and straightforward and clean
as you may think.
Take your time with it, though, and be patient,
and you'll get through your wiring.
It just takes a little bit of finger dexterity
and a little bit of trial and error
until you get it comfortable and where you want it to be.
So now, I have my green, put this on there,
and then my yellow.
So there we go.
Now, our wires are connected to our panel,
and both wires are securely set, so we're
ready to connect the keypad to the other side of the wire.
On the back of our keypad, you're
going to notice that there is a legend right there
on the top that says which terminals get which wire.
Green, negative, positive, yellow.
So green, black, red, yellow.
So then over here, I'm taking the other end
of the wire that's connected to our panel,
and I'm going to connect it to our keypad.
So terminals are open and ready to go.
I'm going to put the yellow one in first.
Now, this process, if you have two people,
it will serve you well, as one person
can hold the keypad while the other person puts
the wires in and screws.
But if you do do it by yourself, again, take your time.
If you need to use a table to put the keypad on top
of while you do your wiring, really anything
you need to do to get these wires in
and connected is what you've got to do.
So the red is the next one, black is the next one,
and then we have green for the last.
Giving a quick tug on the wires will show they're in place
and secure.
And I found that my black is not.
Just by doing that, I was able to see
that this was not connected.
That would have been a troubleshooting nightmare if I
actually powered everything up.
So those type of steps that you take that can just
confirm whether or not you've actually screwed the wires down
are important to do.
So let me just loosen up this terminal.
We'll put the black wire back in,
and then I'll tighten it up.
So we're connected and ready to go.
To snap the keypad onto the back plate,
you just put it into the plate and then push down.
So I put it here.
It's upside down.
I have to spin it.
On the bottom of that, you're going
to notice there's a hole for a set screw.
This set screw looks like this.
And it comes with a screw pack for the keypad.
What it's used for is after we pop it onto the back plate.
On the bottom, there is a place for that set screw,
and that will keep from somebody pulling the keypad off
of the back plate, just an extra security layer for the keypad.
So we're wired up.
We're connected.
We have our keypad mounted on the wall,
and we're ready to power up.
So the next stage is we're going to do
the programming for the keypad, and then we're
going to enable the device address in the actual panel.
Let's check it out.
Before continuing in the next step,
especially with the VISTA-128, you're
going to want to pick which AUI slot
you want this keypad to occupy.
On a 128, we have to go into programming,
we have to pick the slot that we want,
and then program it to work as a slot for a touchscreen keypad.
And it's a good idea, before you get in the weeds with that,
to figure out which number you want your AUI to be on
and to make sure that doesn't conflict with any other devices
that you have installed on your 128.
A lot of times, 128s do support quite a few devices,
so figuring this out beforehand, it's
going to save you a lot of trouble.
What I want to do first is we're in a power
up our panel, which is going to power up our keypad,
and we're going to do some keypad programming
to get it set up to look for that AUI address.
So on our panel, I'm going to plug-in my backup batteries,
and then I'm going to plug-in the main transformer.
So our keypad is booted up.
We have our language selector, we have our operation mode,
and we have our ECP address right there.
This is going to be our keypad address.
So I'm going to pick number six, because I
know that's open on our 128, and I'm
going to head the checkmark.
The is it's gathering information from the panel.
As soon as it finishes doing this,
we can move to our next step.
So our keypad is booted up now, and we're
going to move to another keypad.
Whenever you do install a touchscreen keypad on a VISTA
panel, it is highly recommended that you also
have an alphanumeric keypad connected.
This is because the alphanumeric keypad
is going to be what you use to do your push button
programming, and it's the easiest way
to do this type of programming.
We have a 6160 also connected to our 128,
and this is where I am when I do my programming.
So I have to go into programming and enable the device address
for this keypad to work properly with the panel.
So to do this, I've have to enter the installer
code in an 8,000.
On the VISTA-128, that's 41408123.
We have program Mode, star for fill, pound for view.
What I'm going to enter is pound 93.
Zone programming, we don't want that, so I hit zero.
Expert mode, no.
Report code programming, no.
Alpha programming, no.
Device programming.
That's the one we want.
So to confirm for that, I'm going to hit the number one.
So now that we're inside of device programming,
we have to pick the device address for this keypad.
Now, as we picked keypad slot six, we're going enter 06.
Hit star.
And as you see, it's not used.
So what I have to do is do 01.
Alpha console.
Hit star.
Console partition.
This is going to be the main partition
that the keypad lives on.
And for today, we're going to do partition number one.
I'll hit star Sound option.
We really don't have to worry about a lot
of these other options.
I'm not going to go into them right now.
We'll just star through.
AUI.
This one, we want to say, yes, because it is an advanced user
interface.
I hit star.
After I finish the programming, I'm going to do 00 to quit.
Star.
Quit menu mode.
One for yes, and then star 99 to back out 100%.
Now that we've programmed our 6290W keypad through our 6160,
when it comes back up, it should properly show the panel status,
and we should be able to arm and disarm from our new keypad.
Great.
Right on the top, we have ready to arm.
It's on partition one and has our armed selection.
So let's try it.
Arm Away.
And it's working.
Armed Away.
Exit now.
I'm going to disarm to cancel this, 1234.
Disarmed.
Ready to arm.
And we disarmed it.
If you do have any questions about programming
the 6290, setting it up with a 128,
or VISTA-P panel, or any other questions about this keypad,
as this is a complicated process,
and there's a whole bunch of different things going on
with it, please give us a call at 888-818-7728,
send us an email to support@alarmgrid.com,
or check out our website, www.alarmgrid.com.
If you did like the video, feel free to subscribe.
And if you want to be notified when we post future videos,
hit the notification button below,
and we'll send you an update when we do so.
Thanks for watching, and have a great day.