Once you've exited the trailer you're going to want to lower the canvas door
down making sure that that stays inside the camper then removing the canvas from
each side of the door raise the steps up, and that locks in behind with two blue
tabs and then you will use the key provided to pull the seal nice and tight
Now making your way around the outside of the trailer I'm going to pull all
loose, push all loose canvas inside on your rear bed you will have press studs
on the rear wall of the trailer that will need to be removed make sure that
you remove them individually don't just grab the canvas and give them one big
pull individually remove each press stud and then underneath here there is a zip
undo the zip and this flap of canvas will just go over the top, same on the
other side you've got press studs against the rear wall followed by a zip
along the side and this canvas will go on top, finally once you know that no
one's going to be on the rear bed anymore inside the trailer remove the
support bars so that's done nice and easily by taking the pressure off with
one hand and then grabbing the bar. As you can see now that rear bed is
going to move freely. Coming around to the other side of the trailer tuck all
of the loose canvas in, undo the velcro that goes around the gas struts if you
have done that up and undo the two velcro tabs each side I like to
velcro them together at the top it seems to hold the canvas up out of the way so
there's one of them on each corner of the trailer
put that little tag inside now we're ready to close the beds now we get to
Now we get to close the beds so you're going to close the rear queen-size bed first so
pressing on the bottom right button of the remote control holding that down
you'll hear the power start going to the actuator and then the bed will start to
close, once it gets about halfway so it's in the vertical position I like to stop
at this point I like to have a look inside the trailer make sure that
nothing's getting caught mainly the hoop pole that we lowered
from the rear beds as well as we'll give all of the canvas a pull down onto this
front bed including the tropical fly now we'll lower the rear bed a bit more
once we're up to this point we want to push the canvas down on the inside of
the trailer so we want the canvas to come along the front bed down the
cupboards inside the front and then along the lounge inside so that's just
done by pushing down inside you'll also notice I pushed the canvas away from the
actuator on this side here so I'll just go over the other side and double check
over here same thing pushing the canvas in making sure that it goes flat along
that front bed down the cupboards at the front and then along the lounge inside
now we can lower the bed even more.
So as we're lowering it we just want to stop
just before the beds all the way down you want to double check each side that
you've got all of your canvas tucked in nice and freely and then lower it until
the actuator stops which will be about there so that's now going to as you can
see that's nice and loose that's then going to use the front bed to lower the bed in.
Remove this strap as you can see the gas struts are already doing their job. I do
at this point here like to close the front bed support as well
stops you from forgetting to do it. Now clicking the close button on the front bed.
Stop about there and at this point lower the rear bed in here a little bit and
pull this canvas down flat so now all of those poles have now landed on that rear
bed and it's now lowered it a bit more now we can continue, once we get about
there we'll stop as you can see your PVC is now hanging through the front
that's what stops the drafts coming through at night under the front bed
so each side we''ll just give that a bit of a tuck in.
and now we can continue
the ease of the remote control allows me to walk around as the beds closing and
I'm just tucking both sides in.
As it gets near the end slow it down make sure that
there's no canvas coming through, now give the bed a little bit of a pull
down I latch the clip on but don't pull it down all the way I will do both sides
that way that then allows me a bit of an air gap so I can get my fingers in there
and give it a final tuck, once I'm happy with where it's all sitting you can do
your latches up. So there's two of them on each side and finally turn the power
off to your master isolator.
Now that you've turned the power off starting
from one corner of the trailer go around, close all the doors if you wish lock the doors.
All the doors are locked and closed final thing to do is to raise
your stabilizer legs so using the winder provided raise them
all the way. Supporting the main body with one hand to pull the blue lever out
and then lock it back in position upright give it a bit of a shake make
sure it's not going to fall down