Hi, DIYers.
This is Frank at Alarm Grid.
We're back in the Alarm Grid video lab
working on the 2GIG GC3 panel.
We're going to show you how to swap out
a cellular radio on your system.
You may notice in either of the cellular radio guides,
specifically we're going to be working on the alarm.com
radio's today, you'll notice that there's
the do have the ability to do what's called a cellular swap.
What that means is that when the system is powered on,
you can basically remove one cellular communicator
and put it in another.
The guide is a little bit confusing.
There is mention that you can install your first radio when
the system is powered on.
What we've noticed, at least on our system here in the lab,
is that the feature to begin and essentially
cut power to the cellular radio and allow for that hot-swap.
It's not there unless there's a cellular radio already
installed.
So we already have a video on installing the 2GIG-3GA-A-GC3
radio.
We also will have a video for the 2GIG-CDMAV-A-GC3.
This video here will actually be showing you
how to remove the 3GA or the AT&T radio
and putting in the CDMA Verizon radio.
So you'll notice that when we go in here into Programming
to do the cellular swap, that Begin button will show.
And you can do that swap here in live time.
Again, the first time you install these,
you'll notice in our other videos
you will have to power down the system.
So I'm not sure if that's something
that will be changed in firmware so that those guides are,
in fact, correct with their statement on hot-installing.
It may just be a hot-swap for now,
not a primary initial install.
So again, we'll show you how to do the swap here
with the radio already installed.
And then we'll install our new Verizon radio here.
So if you are in, say, you got this system.
You ended up with an AT&T radio.
And maybe the AT&T coverage has not been so great in your area.
Maybe your Verizon is a lot better.
That's where this swap could be a good solution for you.
So we'll hit-- we'll go into System
Settings on the bottom right.
And this time, we can enter either the master code, which
by default is 1111, or we can enter the installer
code, which is 1561.
Once you're in this field here, we can then swipe down
and you'll see Cellular Radio Swap.
You'll notice that because we have the radio in there
already, it will say select begin
to start cellular radio module.
We can do Begin or Radio Test.
For right now, we'll do Begin.
So in this mode when it says remove the cellular radio,
it has cut power to the cellular side of this panel.
So what we'll do is we'll grab the little tab here
on the bottom side of the door.
And there's a little tab here that
sticks out with an arrow on the side of the radio.
We can just grab that and give it a firm pull.
And you'll notice that now the screen says insert cell radio
module and select Done.
So I'll take our old AT&T unit, put that down.
And we'll take our new Verizon CDMAV-A-GC3.
Before we put this in, you'll always
want to document the ADC number.
So just make sure that you have the ADC.
You might as well just take a photo
of this with your smartphone or you can just
document the numbers on here.
You'll need that ADC number in order
to change over to this radio on alarm.com.
You'll need to give that to your dealer.
So we'll take this.
We want the antenna sticking up and the gold connector
here facing inside the panel.
So we'll just push that right in.
It just firmly sits in there nice and snug.
We'll grab our door again.
And that little tab here, we'll have on the bottom right.
You want to put the three hinges into the back plate first
sitting in there nice and tight and then snap it shut.
Now, once we have this completed, we can click Done.
It will say Working.
And it will take a few moments for that
to give power back to the cellular compartment here.
And as that's doing its thing there,
again, this was swapping out the 3GA-A-GC3
for the CDMAV-A-GC3 You can do the same thing the other way
if you had a Verizon, if you had the CDMA radio in there first
and AT&T happened to be better in your area,
then you could do the same thing,
same cellular swap process here.
It may take a couple of minutes for this
to get power back to the cellular module.
So we'll give that just a few moments here to keep working
and make that physical and firmware swap
inside the system.
These cellular radios give you the ability
to enroll in alarm.com service, which, again,
we've discussed in other videos, but gives you the capability
to set up the alarm.com app where you can remotely
control your system and set up customizable text and email
alerts as well as allow your alarm.com dealer, your alarm
company, to remotely program and configure sensors for you,
as well as other deeper level programming features.
This process, you'll notice, could take several minutes.
So we'll give the panel a couple more here.
And there it is.
It says cell radio module swap complete.
And you could do a radio test now.
We could hit Radio Test.
And you'll see signal strength is four out of six bars.
And it'll actually show you the serial number on there.
It will say registration status Registered.
And it's idle.
So we already have this setup here on the system.
I can back all the way out to the Home screen.
And now we have our new CDMA Verizon radio
installed in our 2GIG GC3.
If you have any further questions on doing a radio
swap on your 2GIG GC3, please email us
at support@alarmgrid.com.
And don't forget to subscribe to our channel.