originally this car was a 2012 lexus ct 200 regular now we got the f4 sport right here
2015 upgrade facelift right there direct bolt-on
big face now
hey guys welcome from revemoto today we're going to be doing a 2012 ct 200h front bumper removal
but we're going to install a different one we're gonna do a 2015 lexus ct200h front bumper but not
just a regular one we're gonna go with the f sport so if you guys like this video go ahead
and like and subscribe to our channel turn on my push notification and hit that like button
at the end of the video if you guys have any questions go ahead and comment down below
we'll answer all those questions for you all right so on this uh old bumper
the regular uh 2012 ct200 we're gonna take off the fog lights first so we're gonna use a uh phillips
so if you guys look right here it's gonna be screws
right there let's take this off well first we're gonna unplug it
so the only screw that we're going to take off is this one
and you're gonna just slide it out like that but we do need we do need these rest of these screws
for the uh installation of the new front bumper so i'm gonna take off these screws right here
and we'll do the same thing on this side take off the screw right here
let's see i think this one you unplug first here's hids so unplug it
if you take off the screw right here
then you'll be able to just slide this off so you just goes in like this
and you slide it off so we're gonna need these screws also for our new front bumper
so here's a new bracket right here for that uh the 2015 f sport but basically
when you put this in right here it doesn't go in perfectly see that it's kind of snug
and it doesn't come out as much as we want so a solution that i found was to
cut that little side right here and then the fog light itself will slip right in there you go
a little simple solution so we don't have to buy a new fog light because these fog lights
were like 200 bucks from the dealership and only dealership had them so just like that we
just cut a little bit simple little solution so for me to cut i just use a uh a razor and
i'm just going to cut the one down here so i'm going to cut the top part
right in the middle and right on the bottom side right here so be careful
all right there you go then this thing should just go right in
there you go all right so once you guys have that fog light in
i'm gonna go ahead and screw it on the top one two right there
all right we got one fog light in place
same thing on the other side so if you guys look at it there's gonna be indentations of like an l
and then this one should say an l right there also
okay so those two screws are in all right so here's our new bumper right here we're gonna
put in the uh fog lights so let me show you guys so once you insert it you should click
and you should hear that click and then right on top there's gonna be these two holes right here
so you're gonna put these two bolts or screws on there
all right so we'll do the same thing on the
other side so hopefully this was a better view so basically just go
make sure it lines up
and then it clicks and then put those screws on
all right once you have the fog that looks like this now
you're gonna get your cover looks like this and then make sure the prongs
match up with the holes
then once they match up you can go ahead and put it down
and you should hear it snap do that on the other side so underneath the
fog light is going to be this holes right here i'm going to put a push pins in them
do that on the other side also all right next step would be to put that black mesh on which is gonna
be this piece right here so just line up the holes and then push down on it once that's in place
we're gonna put the upper one up so just make sure you line it up with the holes in the prongs
so it doesn't have to be all the way in because we're gonna have to screw it on in the back all
right so now we're gonna flip the bumper upside down all right so here's the view from behind it's
gonna be screws right here so it's gonna be right here and another one back here so it's basically
where the top mesh and the lower mesh meets and that's where you're gonna put that uh screw
and if for some reason these prongs right here when you're pushing it from
from the front it doesn't click when you turn it upside down the bumper
you can just put your hand back here so let me show you guys from this angle
so put your hand underneath and then just kind of press down and these prongs should
click into place all right so now the the mesh piece is all together
we're gonna go ahead and get the chrome trim around right here fitted
so again just make sure these uh prongs right here line up with the holes and then you can press down
and then right behind here we're gonna go ahead and screw it in so we got one two
three four screws so just take your time
make sure you line it up before you start pressing down on it it's not lined
up
all right now we're going to go ahead and screw it in place
turn it back upside down all right so if you go behind your bumpers one screw right here
right on the bottom right here is another screw
and then a screw down here and a screw up here and that screw looks like this
i'm gonna do the same thing to the other side all right so so far
our bumper should look like this with the chrome piece on
and the mesh grille on now we're gonna put that top piece on the front bumper
so remember always line it up
once it's all lined up go ahead and push down you should hear a clip
all right here we go all right so now we're gonna turn the bumper upside down and there's gonna be
screws that we need to screw on here and on the other side all right so they're gonna be like
this again and it's gonna be one right here and one right here all right so an old bumper we're
gonna need to take off this emblem right here get something soft like a flat uh plastic piece like
this this is a panel removal tool set i'm gonna go ahead and pry that off but right behind it
right behind this it's a clip right here you just press down on it
and release it like that we'll go to the back where you guys release that uh little pin
go ahead and push if you guys get one of these things
go ahead and tie it out so stuck there with a double stick tape right there
now we got the emblem off so next we're gonna need to take off this rubber piece right here
and it's just uh stuck there with clips so again with something flat
we're gonna try to get those clips off flyer would work too
so basically that strip is held on by these little clips right here
and all you're trying to do is uh push on each side so you can release that clip all right the
last piece of the puzzle we're going to take off the old bumper is going to be the wiring harness
all right so now with that we have the harness off i'm gonna go ahead and put it on the other bumper
so now just go ahead and follow the holes on the bumper and you can put that uh harness on
so the actual harness itself you have to kind of cut this piece and put it into place
and then tape it back down so yeah so just take it off and then readjust it
and then tape it i'm going to go ahead and do that i don't want to bore you guys with that
one all right so now our bumper should look like this we're gonna put that emblem back on
right here all right so now we're gonna put the emblem back on i did double stick tape on there
so you can get that at the regular auto parts store now just line up the holes and the prongs
get into place all right so now you have that um i guess like the weather stripper on the top
just follow the holes with the little prongs right here line up the holes first and then hit it down
on the side of the bumper you'll see these clips right here also take this off and put
them back on the new bumper now that we have all the clips back onto the new one
so this is our new bumper right here make sure you guys have those clips on the side ones too
we can go ahead and uh install this bumper
all right so i'm gonna go ahead and install the bumper grab one one of these nuts that went on
the top of the bumper so we can just secure it while we're holding on to the bumper and then
make sure like you plug in the fog lights also before you actually put the bumper all the way in
when that's lined up go ahead and grab that bolt put it right on the top
it's going to be a little helper right there got two helpers today
all right so now i'm gonna go ahead and put that uh fog light plug in the fog lights
so we're gonna secure one side first and then we're gonna secure the other side so i'm gonna
go ahead and put you guys around so we're gonna go ahead and clip it onto the bracket and then put
the screw on and then right here on the side make sure the um the clips hold on to the fender liner
so you see like i had a hard time it's just because something was
snagging on the bottom so make sure the fender or the engine cover right here
kind of goes underneath goes on top of the bumper
so now that it's underneath
so now get that fender liner and tuck it in behind
all right now we're gonna go to the other side
all right so we're gonna go ahead and put on the other side of the bumper i'm gonna go
ahead and clip it on but make sure if anything's snagging it or it's not going into place correctly
look underneath or look behind it uh this guy's um hid lights were actually hitting the washer
fluid so i take that off so now underneath i'm going to go ahead and put those screws on
all right so next step is going to go ahead and put that cover back on
actually before i put that cover back on let's tighten these bolts up
we're also going to check the gap so
all right well that's looking good all right so now we can go ahead and put the cover back on
last but not least i'm gonna put those covers on
all right guys so that's the conversion right there it's pretty simple pretty
easy it's going to be a 2012 originally a 2012 lexus ct200h and we converted it into a 2015
lexus ct200h not just the regular one remember that this is going to be the f-type
so if you guys like this video go ahead and like and subscribe to our channel
turn on that push notification and hit that like button again if you guys need any pre-painted
auto body parts for your car, go to revemoto.com your pre-painted auto body part source thank you