Hi, DIYers.
This is Michael from Alarm Grid.
And today, I'm going to show you how
you would add a hardwired zone to a DSC PowerSeries NEO
security system.
We have a wired motion sensor here
that we're going to be using for our demonstration purposes.
But first, I want to talk a little bit about the NEO.
The NEO is a hardwired system, and it
has onboard zones for you to add hardwired sensors.
This one has eight hardwired zones on there.
Each zone is set up with an end-of-line resistor that tells
it that the zone is closed.
So you need to have those at each zone,
even if there's a zone that you're not
using with the system.
If you need to go beyond eight wired zones,
then you can get a zone expansion module
to add additional zones.
But in our case, we're just adding
one zone at zone number one so we don't need that expansion
module.
But we do have our sensor here.
And we already have it wired up at the sensor itself.
We did a four-wire connection.
Now, just to be clear, some zones
are only going to use a two-wire connection, in which case
that's just transmitting a zone status.
A zone status is being transmitted between the sensor
and the panel.
That's common for door and window contacts, where it just
needs to know whether it's open or closed.
But in our case, we have a powered sensor,
like a motion sensor.
Another example would be a glass break detector.
They use both power and zone status transmissions.
So we're going to have two wires for power, which
are the red and black wires, and then we
have two wires for zone status, which are,
in our case, the green and the white wires.
So we already have ours I set up,
and we do have an end-of-line resistor
that's wired in series.
So that way, it'll know when the zone's closed.
Remember, you need to have a resistor at each zone.
The NEO comes with 5.6k ohm resistors.
That's color code green, blue, red, gold.
Those are included.
So make sure you have an end-of-line resistor
at each zone.
So we just wanted to show the wiring at the motion sensor.
Since this is a motion sensor, it's
using a four-wire connection with two wires for power
and two wires for zone status transmission.
So we have the red wire going to positive power, the 12 volt;
the black wire going to the negative ground connection.
Those are both for power.
And then for zone status transmission,
so we have the white or yellow wire--
in this case, it's white--
it's coming into the common terminal.
And then we have a resistor wired in series.
So we took the resistor and we put one end
into the normally closed terminal,
and then we used a B connector and a crimping tool
to crimp the green wire incoming with the resistor
at the other end.
So the green wire coming in on one of the zone status
transmission wires isn't connected
to one of the sensor terminals, it's
wired in series with the resistor
going into the terminal.
So that's how you would set up a four-wire connection.
Remember, if you're just doing a two-wire connection, what
you might use with a door and window
contact or a non-powered device, it's
just going to do with zone status wires.
There'll be two wires for zone status,
and there won't be any power wires involved for the sensor.
So for the power connections, we're
going to connect to the aux port right here on the panel.
We're going to do move this backup battery out of the way
because that's kind of in the way.
But we've got here.
So we're starting at the third one for positive.
Actually, I put it into the fourth one there.
Sorry about that.
So we've got the third one here for positive,
and that's for the red wire.
And really, color doesn't matter.
As long as you're matching the color
at the sensor and the panel, then you'll be good to go.
But in our case, we are using proper traditional colors,
so red goes to positive power.
And then we have the black ground wire
for your negative power.
That's going to go into the negative box terminal.
And we got that in there, and it's tightened down,
so they're good to go.
And then we're doing the two data connection wires.
And I do want to point out that each zone on the NEO
uses an end-of-line resistor.
These zones aren't set up, so they're just
set up at the panel.
But our resistor is at the sensor here, end of the line.
And they're there 5.6k ohm resistors.
So that's color code--
it's green, blue, red, gold is the one you want,
and they come with the NEO system.
So just make sure to include those.
Otherwise, it'll show zone open and you don't want that.
So we're going to connect the first one here.
We're doing zone one, and we're doing its common terminal,
and we've got the first data connection here.
Inserted it.
Tightening it down.
And then we have the common connection here, the other zone
data connection.
Open that up, and just insert it into the slot,
and tighten it down.
OK.
And our sensor is nice and secured.
All the connections are good, and so we're going to power
up our NEO system.
We're going to start with the backup battery
so we don't have any scary sparks this time.
There's still sparks, but what can you do?
So we're going to do that.
And then we're going to plug-in the transformer
to provide full power.
So we have our NEO system powered back on.
I'm just going to show you the programming that's needed
for a new hardwired zone.
It's mostly setting the zone definition
and assigning any partitions.
So first, we're going to enter into programming,
so that's * 8.
It's going to ask us for our installer code, which we have
ours at the default of 5555.
And then we're going to enter 001 for zone definitions.
And then you're going to want to find the three-digit zone
number of the one that you're using.
We have ours setup at zone number 1,
so that's the default one, so we can just press * to confirm.
And then it's going to ask us for the three-digit zone
definition.
Now, you should look in the manual for your NEO system
to see the complete list of zone definitions.
But if you scroll through them, you
can see a couple delay options, like entry-exit delays.
You can see an instant.
You see interior.
So we'll go with that.
We'll go with interior, and we'll press * to confirm it.
And then it's going to take us the next zone,
but we don't need to set up a second zone right now,
so we'll just press the # key to go back.
And we'll repeat that until we're back at the main menu.
So that's how you would assign a zone definition.
I just want to quickly show you how you would
assign a partition if needed.
So and we see our camera guy's moving around,
and so that's why it says there's
an open zone on the keypad.
But anyway, so you get into programming, * 8,
and you enter the installer code, 5555.
And that's how you get into programming again.
And so we need to do partitioning.
So we're going to go to 201.
This is for partition 1.
202 would be partition 2; 203, partition 3;
et cetera, et cetera; to partition 8
on most DSC NEO systems.
Some Power Series NEOs will only have six partitions.
So 201 through 206 or 201 through 208,
depending what you need.
But we went to 201 for partition 1 is what we wanted to do.
And so we're going to press * to select.
You can go through and select--
the numbers are organized by groups of 8,
so you have the first eight zones,
then you have 9 through 16, 17 through 24, et cetera.
But we're working on zone number 1.
Remember, we assigned it to the on-board slot 1.
So zone 1.
We press the * key to continue.
And then you're actually just toggling.
Well, you enter the * key to change it,
but you do N for no or Y for yes.
We want ours to yes.
Going back out a bit.
OK.
There we have zone 1 set to yes.
We toggled it.
There.
Zone 1 is yes.
You see it there on the screen.
Good.
And if we press the arrow keys, we can toggle to the next one--
zone 3, zone 4.
So you see that they're all yes.
That's fine.
We were just setting up 1, so we can back out to the main screen
here.
And so you want to toggle that to yes for the partition
you want to do.
Say we wanted to do it no, and we
were doing it for partition 2.
Say we didn't want it to be enabled,
we'd have it set to N, which we see there.
And we're not going to toggle that.
We're going to leave that alone.
We're going to just # to exit.
But make sure all the partitions are correct, so that way,
it's only responding on the partitions
that you want to work with.
So that's how you would add a hardwired zone
to a DSC PowerSeries NEO security system.
If you have any questions about the DSC PowerSeries NEO,
or about alarm monitoring in general,
send an email to support@alarmgrid.com.
And if you enjoyed this video, give it a thumbs up below
to like the video.
And remember to subscribe to our channel for updates
on future videos.
Hope you enjoyed the video.
Thank you.