hey guys drew with geoarm here again to talk to you about the alula bat connect and its connection
into the ge interlogix networks nx series panel uh what we're going to do first here is we're going
to go over the packaging it comes in it comes in this pretty small box here and on this box
you're actually going to have the mac and the max crc that are going to be required for activation
so make sure you document that information before uh you know giving us a call to get that activated
i'm going to go ahead and move this over to the side the next piece of information i want
to share here is going to be the documentation this is the actual manual it'll show you how to
mount it and how to get it wired in of course i'm going to touch on how to wire it in in this video
but uh it'll show you you know visual uh illustrations of how to do this so what
i'm going to do is i'm going to go ahead and flip to the networks page here you can see the wiring
it uh it shows you the connections to make between the back connect itself and the networks
so we'll put this right here so that you can see the connections that i'm making
what we'll do first is we'll pick up the alula batconnect device and get it open there's a little
clip on the side with edges ridges you just press that down and you separate the top from the base
and as you can see we have it opened up now and i have it pre-wired this is not how it comes uh
i've i've done this just to save time in the video so what we're going to uh what we're going to need
here uh before you know you even get started on this installation is you're going to need a
strip of 18 to 22 gauge wire stranded there's gonna be three connections from this one this
is a four conductor so if you look i've already stripped this wire and pulled this one back so
it's not interfering and these three are the only ones that remain here so uh and i've wired them in
so those are the three connections we're going to be using we'll use green black and red from
this one and then this is a strip of 22 gauge two conductor wire here and uh this wire is going to
be used for the communications so this is a this is a completely separate strip so you need two two
lengths of wire um so we'll go ahead and get this first one wired in so what you're gonna see here
is that i've wired the green wire from this to gn which is located here
right here so it's already wired down then we skip the one directly to the right of it
which is labeled yn nothing is going to be going into there we're going to move on to
gnd which is where the black wire is going to go it's right here and directly to the
right of that we're going to put the red wire into 12v which will be the
positive power as far as communications go this strip of wire has a red and a black
so i've wired them in just using the red and the black so the red goes to ring ring
and the black here goes to tip tip so once you get those put in place get them tightened down
it should look like this when it's wired in all the way so you should have five connections
now what we'll do is we'll get them wired into the actual networks itself
so we'll wire in for power and data first so what we'll do is you'll see pause com and data
these three terminals right here pause com data so we're going to take the red wire
there's going to be other wires in this more than likely so just make sure that you put this
in there along with them instead of removing whatever's in there and then get it tightened
down for the red wire which goes to pause the black wire is going to be going to calm like so
and then the green wire is going to be going to data like this once those three are in place
then we can go ahead and move on to getting the communications wired in which is going to
be this wire that's by itself the two strip so just to go over the connections we've made thus
far we have the green wire going from the gn to data we have the black wire going from gnd
to com and we have the red wire going from plus 12v or 12v to pause on the panel so now this is
going to be the tip and ring connections we're going to be making down on the very end down
here you're going to see the four phone terminal slots if there is anything in these four terminals
go ahead and get it out of there it doesn't belong there that's going to be t1
tr and r1 those are the four terminals labeled so we're going to go the black wire here which
is labeled tip on the backconnect is going to be going to t inside of the panel so t for tip
once you have that tightened down you're going to grab your red wire and that is going to be
going to r which is ring and that says ring in the back connect so ring to r and then tighten it down
at that point you are ready to go this thing is connected to the panel and you can get your
internet plugged in right here and at that point it will be ready for activation so give us a call
and we'll be able to get this done with you i hope you guys enjoyed this video and if you
have any comments questions or suggestions please leave them below you guys take care
make sure to subscribe to our youtube page and click the show more tab underneath the
video where you can view valuable links pertaining to this product
similar how-to videos and our low-cost no contract alarm monitoring services