Tokyo 2300 DC welder 200 amp power, high-frequency ignition and pulse function
Jobs can be saved and called any time.
MMA (stick welding)mode 170 amps with Hot Start, Arc Force and Anti Stick function.
Comes with TIG Torch WP-17 (16 mm square cable) 4 meter long with 9mm connection mandrel
a 5 wire control cable and a quick connect coupler on the shielding gas line
Negative electrode clamp and cable (16 mm square cable) 3 meter long with a 9 mm connection mandrel
MMA electrode holder (16 mm square cable) 4 meter long cable with a 9mm connection mandrel
A gas connection hose with 2 hose clamps, to connect a compressed air supply to the welder for Plasma cutting function
Includes gas nozzles sizes 4 to 7, a short and long TIG torch end caps
Collet and collet bodies, size range 1.6mm to 2.4 mm.
Device-specific operating instructions in German and English.
Fit gas connection hose to the connector at the rear of the welder. Connect other end of gas hose to the pressure regulator provided. Connect gas supply to the input side of the pressure regulator
Connect to electrical control cable, to the welder ensure to align the notch correctly on the plug in connector with the notch on the socket on the front of the welder
The TIG torch is connected to negative output terminal on welder.
Attach the shielding gas line quick coupling connector on the TIG torch to the gas line quick connector on the front of the welder
The Earth clamp is connected to positive output terminal on the front of the welder.
Different welding application, require different diameter welding tungsten tip electrodes
Torch angle (angle of tungsten electrode) is also important for your welding application and weld setup.
Check selected tungsten electrode fits into the collet with no excessive play.
Collet body and housing are labeled with the diameter of the appropriate tungsten electrode.
Screw collet body into the welding torch from below, insert the collet into the collet body from the top of the welding torch
The tungsten electrode, protrudes about 2 to 3 cm from the collet body.
The tungsten electrode is fixed in exact position when the the torch back cap is tightened.
The gas cup type and size is selected according to the welding application and screwed onto the TIG torch.
Fine-tune how much the tungsten electrode protrudes from the gas cup with the torch bac cup.
When you switch on the welder, the set welding current is shown on the LED display.
The top right corner of the control panel contains the overheating indicator and the operating indicator.
The top button on the right side of the control panel is used to set the torch button from 2 to 4 cycle mode.
The middle button on the right hand side sets the welder function, from MMA (Sick Mode) to TIG mode
The lower button on the right hand side of the panel turns the Pulse function on and off
The two lower buttons on the left side of the panel are for job selection and saving
The top indicators on the left side of the panel are for Hot Start, Arc Force, and Anti-Stick settings
Using the one-piece knob, you can now make further welder setting adjustments
Press control knob to select the welding final current from time from 1 to 200 amps.
Press the control knob to select the welding current decrease time and twist to set from 0.1 to 10 seconds.
Press control knob to select the welding current stop amperage from time from 10 to 200 amps
Press control knob to select the shielding gas post flow time from 1 to 10 seconds.
Press control knob to select the shielding gas pre flow time from 0.1 to 10 seconds.
Press control knob to select the starting current flow from 10 to 200 amps
Press the control knob to select the welding current increase time and twist to set from 0.1 to 10 seconds.
Press the control knob to select the pulse duration and adjust between 10 to 90 percent.
Press the control knob and set the pulse rate frequency from 1 to 200 Hertz.
When you have made the necessary settings, you can now save your job by pressing the Save button on the control panel.
To do this, select one of nine saved locations and press the Safe button. The job is now saved.
If you then adjust the device and press the Job button, the stored job on the device is set again by pressing the Job button again.
For MMA welding, clamp the electrode holder to the negative welding power connector. And the grounding clamp to the positive welding power connector.
Switch from TIG mode to MMA mode.
The welding current can be adjusted from 10 to 170 amps using the control knob.
Press the control knob button and twist to , set the Hot Start from 1 to 10. 1 = 10 amps, 5 = 50 amps, 10 = 10 amps.
Press the control knob button and twist to , set the Hot Start time from 1 to 10 seconds.
Press the control knob button and twist to , set the Arch force from 1 to 100 amps.
Note the hot start and the welding current can be a maximum of 170 amps
If the welding current is set at 170 amps the arc force setting has no function.
If you have any further questions about the product, please contact us