Now, I'm gonna remove the rear wheel, use a 22-millimeter socket to take the lug nuts
off.
And now, remove the wheel.
Now, I'm gonna take the caliper bolts out, use a 14-millimeter socket.
Now, I just grab the caliper.
Just rock it back and forth a little bit.
And slide it up.
Now, just take the caliper, use a caliper hanger.
You can put it around the coil spring.
Just set it on the upper control arm.
And take the brake pads off.
Now, we're gonna take the caliper bracket off, the bottom bolt is a 13-millimeter socket
you're gonna use.
Take that one off.
And the top, you're gonna use an 18-millimeter socket.
Take those two bolts out, and then slide the bracket right off.
Now, take the screw out.
Just use a T30 socket.
Then grab the rotor, slide it out.
If it's stuck on there, you can use a hammer and just hit in these areas.
Just try not to hit the lugs.
Now, I'm just gonna clean up the hub surface, you can use a wire brush or a die grinder
just be careful.
Just take some of the rust off.
Now, we're gonna take some anti-seize and just do a nice thin coat.
Before I put the rotor on, as you're putting it on, if you have to adjust the parking brake
assembly, the adjustment is right here you can tighten it up or loosen it accordingly.
Now, take the rotor just slide it on backwards first, take some brake parts cleaner, and
just wipe it off.
And flip it around.
Make sure you line up the hole with the hole in the hub.
Clean this side, and wipe it down.
And now, install the screw.
And snug it up.
I just take the brake caliper bracket, take these clips off.
Just use a straight blade screwdriver.
Then clean up some of the rust under here, you can use a wire brush.
Just clean it up real good.
Spray it down with some brake parts cleaner.
Take a little bit of caliper grease.
Just put a thin coat right there.
Take the new clips, slide that in position.
And just take another thin coat of caliper grease, and then do the same for the other
side.
Now, take the caliper slide pin out just like that.
You take some brake parts cleaner.
Clean this off, wipe it down.
If it's extremely dirty, you can spray some brake parts cleaner down here, and then wipe
that out.
Just clean that out.
And take the pin.
And just put some brake caliper grease on there.
Slide it in make sure the seal is properly sealed.
And do the same for the other side.
Now, take the bracket.
Slide it over the brake rotor.
And put the bolts back in.
You can use some thread lock adhesive on the bolts if you want to.
Get those started.
Now torque these bolts to 96-foot pounds.
Now, we can put the brake pads on.
Now, for the inside pad, you're gonna use that that has the warning indicator or the
squealer.
And that squealer is gonna go to the top, just like this.
And then, the one without the squealer goes on the outside.
Now you can take the brake hanger off.
Take the break caliper and use a brake caliper compressing tool.
And just slowly compress the caliper piston.
As you do this, fluid's gonna go through the lines back up into the master cylinder.
And put the caliper over the brake pads.
And put the bolts back in.
And then, we can torque these bolts to 20-foot pounds.
Now, put the wheel up.
And put the lug nuts on.
Now, I'm gonna torque the lug nuts to 100-foot pounds in a star pattern to tighten the wheel
down evenly.
Let's go around again, double-check.
And now, we're gonna pump the brake pedal nice and slow.
There's gonna be an air gap between the caliper piston and the brake pads.
So, we'll get rid of that air gap.
Once it feels good, you're all set.
And check the brake fluid level and adjust accordingly.