Hey, DIYers.
Jarrett with Alarm Grid here.
Today, we're going to discuss what
batteries you can use with the Honeywell SiXCT sensors.
Now, the batteries you can use are 3V or lithium 3V CR123A
batteries.
Now, the lifespan for these batteries
are about five to six years with standard use.
And if you ever needed to change out the battery,
it is very, very simple.
And any end user should be able to do it
because it is very simple.
Now, these Honeywell SiXCTs are only
able to accept one battery each.
They cannot use two or more batteries.
It's only one battery.
Now, to give you a little back story about the Honeywell SiXCT
sensors, these are door and window contacts
that you would use to basically monitor any doors and windows.
And when you're setting these up,
you want to make sure that you're
setting up the magnet and the sensor
at the appropriate distance.
So for example, I do have a Honeywell SiXCT sensor
here with the magnets.
And when you're setting these up,
normally you're going to put the magnets on the door
frame or the window frame.
I mean, you're going to have the sensor on the door
frame of the window frame.
And then you're going to have the magnets normally
on the door or the window itself.
Now, when you're setting these up,
we do recommend that you have the magnets and the sensor
at least touching or very close to each other.
But worst case scenario, if there's
a gap or anything like that, then you
can push out the magnet about 3/4 of an inch from the sensor.
So you want to keep that in mind when you're setting these up.
Now, the Honeywell SiXCT sensors are
designed to be able to be used with the Resideo Lyric
controllers.
Now, the communication method between the system
and the sensor is going to be encrypted.
It's going to be using a 128-bit encryption.
Now, when you're using these sensors, whenever the magnet is
pulled away from the sensor, for example,
you have the magnet in the center sitting right here.
And if the magnet were to be pulled away from the SiXCT,
it's basically separating from the metal
read switch on the inside.
And this read switch then triggers a signal
that the sensor has been opened or the door or window
has been opened.
And it will send a signal directly to the Honeywell Lyric
panel itself.
And again, that signal is going to be encrypted.
It's going to use the 128-bit encryption
method to send out that signal.
So like all wireless sensors, they
do use battery power to be able to send out alarm signals
and send the status or show the status.
So the action of the Honeywell SiXCT sensor
is actually all mechanical.
And the battery is mainly used to be
able to allow it to send out the alarm signals
and show the active status over to the panel.
Now, there's a couple of different batteries
that you can choose from for the SiXCTs.
And that includes the lithium 3V CR123A battery.
And then you have the Duracell DL123A, the Panasonic CR123A,
and the Honeywell 466.
Now, these batteries are compatible with the Honeywell
SiXCT.
And we do also have them available on our website
too if you want to take a look at that.
Now, when the Honeywell SiXCT communicates with the Honeywell
Lyric system, it is sending out the active battery status
as well.
So if you ever wanted to check the battery status
and see where you're at with that sensor, just hop
into the Lyric, go into the certain zones,
you can check it within the zones.
And you'll be able to see that battery status.
Now, the batteries for the SiXCT, as I've well mentioned,
they use 3V.
Now, whenever the battery drops below 2.3V,
that's when the sensor is going to send out a low battery
signal.
So you can swap it out accordingly
with one of the batteries I had mentioned.
So whenever you get a low battery for that sensor,
you always want to make sure that you change out the battery
so you don't get an RF supervision loss for that zone.
This is very important, especially
if you want to make sure that the different areas are secure.
Now, whenever you're changing out
the battery for the Honeywell SiXCT,
it's very simple, as I said early in the video.
Basically, you just pop off the front cover.
And you'll see the battery in the inside.
And you'll be able to take it out, just put the new one in.
So as you can see, I do have a Honeywell SiXCT right here.
And what you'll do is basically you're just
going to slide the cover off.
Just push this cover and take it off.
And as you can see, we have the battery in the inside.
We have the tamper switch.
Obviously, our battery is working right now,
so we have the light blinking.
So what you will do is you're going
to take out the old battery.
And when you're popping in the new battery,
you want to make sure that you have the polarity correct.
Right on the plastic, basically past the circuit board,
you'll see a plus sign and a negative sign near the top
and bottom.
So when you're putting in your new battery,
you want to make sure that you're aligning
the positive and negative.
So right now, our negative is at the bottom
and the positive is at the top.
So let's say we have a new battery, you just slide
that in place.
Make sure it's nice and snug in there.
And you're basically just going to slide on the front plate.
Again, so one last thing to add about the Honeywell SiXCT
is that if you did want to check out an installation guide to be
able to change the battery for this,
there is going to be a link in the description below,
so that should be able to help you out with doing that.
But if anything, as I showed, it is very simple.
And those are the batteries that are
compatible with the Honeywell SiXCT sensors.
If you have any questions about the Honeywell SiXCT
or alarm systems in general, please
contact us at support@alarmgrid.com
or go to our website, alarmgrid.com.
If you find this video helpful, please like and subscribe.
If you want notifications of future videos,
please click the bell icon.
This is Jarrett with Alarm Grid, give yourself a great day.