hello everyone please welcome and join
me Easy Steps today I'm going to share
with you my Hummer h2 I'm going to
change the headlights from OEM to LED
headlights I'm using from Auxbeam and
these are f16 series and it takes nine
thousand seven these LED lights nine
thousand seven they don't have form fit
function where you can take it out of
the box and you put it inside and you
lock it and it will work it does require
a little bit extra step which rework
need to be done in order to make it fit
that part I'm going to share with you I
haven't done it two ways one way I will
share with you that removing the screws
form led then installing it the second
way I'm going to share with you how you
can put the locking nut and without
removing any screws so you can place it
into the socket so it's pretty easy and
a simple process but if you follow it
and you can do it to yourself it's
really easy to replace
so the existing bulb there is a clip on
the back lift the clip and once you lift
the clip and this will comes out and
this is the adapter so this is the
connector going to get replaced as for
existing bulb is very easy if we rotate
this one it opens up and you take it out
and it fits only one way if you look at
these groove those three groove one two
three they goes in here and once we put
it in here then we turn around clockwise
a lock
anticlockwise it opens up and keep it in
safe place so you don't lose it and this
is the bulb so you just pulled it out so
this is the existing bulb we're taking
out now this is the led the way it fits
in it is small notch and then two
notches on the side this small notch goes
right here into the small tab the one
here I'm referring to this small tab
right here goes right in here so the way
it goes we drop the led straight and
then press it down and it seals it once
it seals it now we got a problem we
cannot put over cap on top which is the
locking cap the reason is the heatsink
start causing a problem because it's way
too big
I found a way or you can install it I'm
going to take this one off I found it
the easier way to do it
get a small screwdriver lift the O ring
and then just take the ring out
once you take the ring out there is the
one screw right there and one if I turn
around is a backside you need a small
screwdriver which is a
philip we need to take this out
so you take it off makeup is that you
don't lose the screw and now there is another
screw so we're going to come back
this one is really hard so as
I've shown you that you remove the
screw then you pull this one down and
once you take it out then we insert into
this cap once we insert it in the cap
its fits like this then you slide it
back then you put the screws back again
and you put the ring back once you put
the ring back it's all ready to go
so we're going to insert the LED and It
will sit perfectly fine and then we're
going to rotate the cap then it lock
in use the tie wrap or use electrical
tape to tie up the connector so won't
hang wrong on other side so the LED the
same way as I've shown you how to
install the LED I remove the bulb so I
install the LED and the second one I
left it as is and I'm going to turn it
on and you will see the difference so it
will be comparison at the same time oem
vs LED so let me turn it on 1 2 3
look it at how bright LED light and that's oem
it's a yellowish color and this is white
bright light i going to turn it off
or replace it with the new LEDs and then
I'm going to share what I have shown you
on other side which we put the LED that
remove those the two screws then you
pull this one out then you put this
locking nut on top of it I found another
way you can do it to put it to the
locking nut on top of it and you press
it down one end it goes down once it
goes down then you rotate it once you
rotate it then the second one comes you
press it again
the third side also you press it again
so this is the way it freely goes down
only the problem is we cannot put it in
top side because the heap sink is too
big
same thing we're going to put the
smaller notch and the two bigger smaller
goes on the top with drops in on the top
once it's seated then we can turn around
locking nut and it locks in in place we
can put the connector back you can use
the tie wrap I'm gonna use a tape so I'm
going to tie it together so it stays in
one place so it's not going to move
anywhere and the other side we can put
it right here
another tie wrap or tape as I'm doing it
right now
once it's tie together it's not
gonna go nowhere so this is how we're
going to do it it doesn't take that long
and I'm going to close it lock it
I going to turn on and see how they look so this is how it's
easy and simple to upgrade your
highlights to LED lights on Hummer h2
this is the original OEM and I hope this
video going to help you out and I'm
going to provide the link under my
description if you want to change your
headlight to LED lights then please
check it out like always please like
share and subscribe easy step thank you
bye bye