Hi, my name is Adam, and I work for HP. Today I am going to show you the unboxing and setup
of HP LaserJet Pro MFP M127fn printer.
Here is the HP LaserJet Pro MFP M127fn printer.
First, break the tape and pry the box open.
Fold back the flaps so the items can be easily removed from the box.
The first items in here are the installation CDs for both Mac and for Windows. You'll want
to use these when installing for the first time.
This piece of paper is your limited warranty in Spanish for Spanish regions.
This booklet is your multi-language installation guide for your printer, which provides basic
setup and troubleshooting information.
The last piece of paper talks about the benefits of visiting hp.com/support,
which includes technical support, self-solve tools, and online assistance.
This is the input tray, which we will attach shortly.
Next is the 2-wire phone cable for setting up your printer to fax over a LAN-line.
The last item in the top of your box is the power cable, which we will show how to set
up in a minute.
Pull out the styrafoam and set it aside for recycling.
With that removed, you can now remove the printer from the box.
It's easiest if you set the box on its side, and then work the printer out of the box.
Since this printer is heavy, use caution when you slide it out.
Now you can remove the plastic from around the printer, and then set it aside for recycling, as well.
When the plastic is removed, you can then remove tape from all sides of the printer.
I start at the top and the sides, and then work my way down.
The tape and plastic around the printer are designed to come off fairly easily and not
leave any residue on the printer.
Make sure you get the tape off both sides to get access to the cartridges later.
Don't forget the pieces in the ADF area.
Remove these pieces as well to get access to the inside of the printer.
To get access to the cartridge area, you will have to lift the top cover.
Extend the output tray.
Lift this piece of paper to get access to the styrafoam so that you can remove it from the printer.
Remove the Energy Star sticker from the front of the printer.
Then you can remove the middle styrafoam piece.
Now you can remove the orange plastic and paper from the cartrige access area.
Then pull up the toner cartridge and set it aside. Remove any other tape from the sides and front of the printer.
Now you can remove the protective sticker that is over the control panel.
Now on the toner cartridge, remove the plastic orange piece covering the contacts by lifting them straight up.
This will properly expose the contacts on the cartridge, so they can contact the printer
properly.
Next we will remove the protective tape by pulling the tab from the cartridge.
Grab the tab in one hand and hold the cartridge firmly in the other, and pull until the tape
is freed from the cartridge.
Now we can install the cartridge into the printer making sure the tabs on the cartridge
match up with the tabs on the printer.
Once the slots and the tabs line up, slide the cartridge straight down until it slides into place.
Close the cartridge access door and then close the top cover.
Now remove the input tray from the plastic and remove any tape that is on it.
There should only be one piece of tape holding the paper length guide down.
The easiest way to install the input tray is to set it flat on the table and just slide
it into the printer until it snaps into place.
Then you can adjust the paper length guide and the paper width guides.
At this point, we can connect the power cable to the printer.
Go to the back of the printer so that you can access the power port.
Then remove the twist tie from the power cable. Once the twist tie is removed, insert the
power cable in to the back of the printer.
Once that is firmly in place, insert the other end of the power cord into a power source.
We recommend plugging the power directly into a wall outlet, but for this video, we are
using a power strip.
Turn to the front of the printer.
From the front, you can adjust the control panel using the tab on the side,
and then press the power button to turn on the printer.
While the printer is setting up and initializing, you can load paper into the printer and adjust
the paper width and length guides.
Next we will set up the language and region for your printer.
Select your language using the right and left arrows, and then press OK.
Then choose your region or location, again using the arrows and press OK.
Now lets check to make sure your printer was set up correctly by printing a Configuration Report.
Press the Setup button that looks like a small wrench.
Use the arrow buttons to scroll to Reports, and then press OK.
Then, from the Reports menu, scroll to Config Report and press OK again.
The Configuration pages will print showing that you have set up your printer properly.
If you want to set up your printer to fax, you can remove the 2-wire cord provided with your printer.
Plug the cord into the port on the back of your printer.
The other end of the cord should plug directly into your phone outlet.
Remove any plastic you may have missed earlier.
This was the unboxing and set up of the HP LaserJet Pro MFP M127nf printer.