hey everybody geoarm security here and as promised we're gonna show you the
DIY Home security system installation of the 2gig gc3 so the first thing you want to do is if
you have a box cutter handy go ahead and slice the external pack it down the
middle
open up the box like so you want to remove all of the shipping items and
bubble wrap and place those to the side like so you'll see inside you got
your contacts your key for the motion detector and the all-new gc3 so you
can go ahead and for now you want to go ahead and remove the gc3 package
and everything else that comes in the box
motion your contacts and you have your key fob so that's everything that should
come with the basic kit that we sell on our webpage which I will provide in the
link below now that you have everything out of the books were gonna be working
with the Gc3 I'm gonna show you the things that you need to do this in order
to get it up and running with us it's very simple so for the time being you
can go ahead and removed the accessories out of the way and we're just gonna be
working with this gc3 package locate the sticker here there's a little
tab which you want to go ahead and remove and that will allow you to open
up the gc3 package box you have your guides and you have your installer tool
box I like to just remove the cardboard out of the box keep that to the side now
you got your gc3 panel here go ahead and remove that out of his box proud of his
little packages protector here but that's beside you can remove the screen
off of the gc3
with all the other contents as well this is your transformer box so I like to
just go ahead and remove the transformer
the packaging box you can go ahead and seal up placed directly back into the
box
go ahead and remove the mounting anchors and screws and then go ahead in place
everything else as far as packaging all together in one place so you don't lose
it and you can see all that up now we're left with the panel the transformer and
the mounting screws and brackets now I'm gonna show you how to wire the
transformer so that we can get power to this Dec three panel you will notice
that I have some 22 gauge by two wear cut to the length that i'm gonna need to
reach between the panel and the transformer
mounting anchors and screws I'm not gonna need for the time being replaced
those to the side and I want to show you something here to the left
I've cut I prepared this 22 gauge by two wire and a little bit differently than I
have on the other end this and I used less copper or there's less copper
expose which is gonna go directly into the panel and then this and I'm going to
use for the transformer and I like to have hooks that way it's days more
secure I will begin with wiring and the transformer so you want to locate the
red wire and the positive terminal that's what we'll be working with and
make sure you unscrew just a little bit of the positive terminal and go ahead
and hook this red wire around the back and make sure that it stays in their
secure do the same for the black wire
they are given a nice little tug make sure that it's in their secure now that
you have the transformer wired up take the other end of the 22 gauge by two
wire and you're going to run it behind the back part of the mounting plate like
so that way when you go to seal the panel up the wires ready to go and you
can't believe that there now when you open up this little tab this is the most
important thing is you want to locate power minus and power plus those are
both located over here so this one right here will be power minus and then this
wannabe power plus so now that you have the back plate and the wire running
through it go ahead and install the black wire into the power negative and
screw that down you want to screw it into tight you know I cracked the
terminal but do the same for the red wire as well give that a nice hug make
sure that there's no co-operating expose and you can go ahead and put back on
that mounting plate one of the neatest features on this actual panel is the
communicator is a slide in slot so if you're looking at the panel like this
now would be the chance to install your cellular communicator well your power
down so all you do is locate this little tab you would go ahead and pop it open
and you first get the serial numbers off of the communicator and then you would
slide in either the AT&T or Verizon version which this is so much easier is
very innovative and neat feature and then it would just seal up after you
have verified that you have installed the transformer correctly for power to
the GC3B which has Dc power meaning you do need to be very careful how you
wire you need to make sure that you follow exactly how we showed you have
plugged in the transformer so the panel has loaded and you can see that the home
screen your next objective is to get the zones and context programmed into the
panel with the first way you can do that is if you're signing up
GEOARM alarms alarm monitoring we will be able to assist you with that remotely
when we schedule your appointment if you just wanted to do that before your tech
appointment or if you're just trying to program them I will provide links on
each individual item on how to program them into the all-new 2gig gc3
panel please make sure to subscribe to our YouTube page for more videos and
your blog at DIYsecurityblog.com if you need to reach us by phone our
numbers 1877 443 6276