[THIS VIDEO CONTAINS NO AUDIO]
[HP]
Installation of the HP LaserJet MFP E725 Products
the HP LaserJet Dual Cassette workgroup feeder,
and the HP LaserJet spacer.
Note: The HP LaserJet spacer is only required is a stapler/stacker
or booklet finisher will be attached.
Remove the HP printer from the packaging.
Remove the plastic.
Tile the box to flip the printer out carefully.
Place the printer right side up.
Flip the printer onto its' side.
Notice the rubber stoppers at the bottom of the printer.
Also notice the wheels and latches.
Grab a screw driver and unscrew the rubber stops off.
You will remove everything attached on the bottom of the printer.
Grab the second tier for the printer.
Lay the second piece flat down.
Screw on all the wheels onto the back of it.
There should be 4 wheels after you are done.
Attached the ,metal placements for the rubber stoppers.
Align the metal latches to the holes on printer.
Once verified they are aligned, screw them in for security.
There should be 4 screws total for on metal latch.
Then place the plastic wheels on.
There should be 3 big wheels.
Lay the first piece on its side next to the second tier.
Then lift the second piece on its side.
Grab the extra pieces that are attached on the other side.
Notice the placements on the side.
Place the piece right side up.
Two people will need to pick the first piece of the printer up
Be sure it's aligned with the bottom piece.
Place the latches on the bottom side of the printer.
Push them in all the way.
Screw them in for security.
Remove the packaging tape.
Open the tray and remove any packaging inside.
Open the top tray and remove any packaging.
Remove the paper of stickers for the printer.
Set aside.
Continue to remove packaging tape.
Close the top tray up.
Open the second tray and remove packaging materials.
Close the tray.
Open the box.
Remove all the packaging material.
On the main printer piece, pull the lever on the side.
You will need 4 people to lift the printer up.
Place it on top of the piece you put together on the side.
Be sure the metal pins align with the corner of the printer.
Remove the packaging material.
Open the top cover, and remove tape.
Pull the document feeder from the printer.
Set aside.
Remove the packaging that was inside.
Notice the red warning tape: First unscrew the screw from placement hole.
Grab a screw driver and place in the big hole within the red tape.
Remove the screw.
Peel the red warning tape off.
Continue to remove the tape from the printer.
Open the tray 1 and remove materials
Close the tray.
Open the second tray and repeat.
Close the tray.
Remove the last of the tape.
Pull the warning tab out from the compartment.
Peel the tape off the lever.
Remove the foam packaging.
Remove tape on other side.
Close the compartment door.
Pull the red warning sticker down.
Then pull it straight out.
Open the side tray, and insert it inside the printer.
Grab the big plastic cover and remove it
Notice the black latch on the side.
Remove the packaging to the feeder.
Pull off the plastic cover with foam in it.
Pull the red plastic off the feeder entry.
Remove the blue tape.
Notice the sticker on the edge.
Remove it.
Set aside.
Pull the red tape off.
Place the feeder into the printer.
Screw the top tow corners to secure.
Plug the wire into the port on the printer.
Close the front door, and you'll notice on the side the tab will show after locked.
Place the cover back on.
Close the tray.
Place the stickers in the upper right corner of each tray.
Place the plastic holder on corners of the bottom of the printer.
Notice the bar code stickers that came in the packaging and it matches with printers bar codes.
Upgrade firmware with the latest available on hp.com.
Insert a thumb drive at the connector on the control panel and select the following:
Note: All accessories must be attached when upgrading firmware. Accessories attached later will not be upgraded automatically.
Support Tools > Maintenance > USB firmware upgrade
Find more video like this at: hp.com/SupportVideos, youtube.com/HPPrinterSupport
Continue the conversation: hp.comSupportForum, facebook.com/HPSupport, twitter.com/HPSupport.
[HP]