Brought to you by 1AAuto.com, your source for quality replacement parts and the best
service on the internet.
Hi, I'm Mike Green.
I'm one of the owners of 1A Auto.
I want to help you save time and money repairing or maintaining your vehicle.
I'm going to use my 20-plus years' experience restoring and repairing cars and trucks like
this to show you the correct way to install parts from 1AAuto.com.
The right parts installed correctly.
That's going to save you time and money.
Thank you and enjoy the video.
In this video we're going to install a new Pitman arm on this 1996 Tahoe.
It is the same as any 1988 to 1998 Chevy truck.
This is a four-wheel drive vehicle.
So four wheel drive trucks and also 1992 to 1999 SUVs, four-wheel drives.
You will need the following tools: penetrating oil, a whole host of mm sockets, 18-mm fitting
wrench, joint fork and hammer Pitman arm puller and actually not listed here was a 19-mm socket
and ratchet or your tire iron to remove your tire.
You'll also need a jack and jack stand or lift.
To check and see if you have a bad Pitman arm you can see where this front driver's
side tire we're going up and under.
Here's your transfer to here and then up right there is the joint of your Pitman arm.
This here is your Pitman arm and then this is your steering linkage.
Again, here is your Pitman arm.
Here's your steering linkage.
Now when you move your tires, I'm just grabbing hold of the tires and kind of turning them
back and forth when the car is above the ground and you can see there is a lot of play and
movement going on around that Pitman arm.
That joint is bad.
First, you'll want to remove this skid plate which is four 15-mm bolts.
You can see two easy here, and there's one up here and one you cannot really see, but
over here.
Now we're going to remove the steering box to get to the Pitman arm.
Okay.
So, this is the driver's side of the engine compartment.
There's the power break booster and this right down here is your steering box.
It's a little difficult to see.
It's where you can see these tubes going in.
There is a plastic shield here.
It kind of clips around.
Now you can see this was clipped up and around here.
You just kind of peel that off and pull this plastic shield back and now you're going to
want to use some penetrating oil and douse both your fittings, one here and then one
a little further up.
It's kind of difficult to see.
There are two fittings to douse with penetrating oil and then there's also a bolt.
You might be able to barely see there and then you also want to loosen this bolt here
and that loosens the coupler from the steering box shaft.
The best tool for removing those power steering fittings is a fitting wrench like this, 18
mm.
See it down on there?
I got it on there and then once you loosen it with a fitting
wrench you can usually get an open-end wrench on there to help you navigate it the rest
of the way.
Then, make sure you have a catch pan underneath to catch the fluid as it starts leaking out.
Now we're going to use an 11-mm socket and ratchet and extension to loosen that bolt.
Down in there put the socket and ratchet on there.
At this point it might be good to have someone help you just hold the steering wheel so it
keeps that from turning at all.
Once you remove the bolt then you want to take a large screwdriver or a pry bar and
put it down in there and just make sure that you can move the steering shaft away from
the steering box and if you watch you can see that the shaft is moving from the steering
box pretty easily.
When I actually unbolt the steering box I'll be able to pull it right out.
No from underneath here's the front of our transfer case on this four-wheel drive truck
and this is our Pitman arm joint right here.
So, it's a 21-mm bolt.
I'll use an impact wrench.
As you can see we removed the tire over here and this is a joint fork.
So, we're going to bring it in from the side here and then use a good hammer.
Basically we just removed the tire so we can get a good wrap on this fork.
Okay.
You see that fork just separates that joint.
Now we get to the three bolts that hold your steering box on and I just used a little screwdriver
kind of bend this fender up a little bit because it was in the way and you can just tap it
back down with a hammer when you're done.
Then you can easily get a socket and extension on there, and just to show you it can be done
with hand tools, again, 21-mm.
I'll just do the rest of it with an impact wrench just to be quicker.
Hold on to the box with one hand.
If not it's just going to fall out.
Move it up and out of the steering gear and pull it forward from the shaft.
Here's the bottom of it.
Put the steering box here, upside down, once again just so any more fluids just drain out
into the pan.
Here's where having an impact wrench is going to be really valuable.
Then this socket is a 34 mm.
If you don't have an impact you can just turn it on all the way and then use a large bar.
You may want someone to help hold it.
You could bolt your steering box onto a longer piece of wood which would help you to keep
it steady, but having an impact wrench is the best way.
Now, you're going to want to use your Pitman arm puller.
This is really the only way to do this.
Believe it or not I actually forgot to film, or I messed up and I didn't film pulling the
Pitman arm off so I'm just going to show you how to use the Pitman arm puller and the tool
on to the idler arm.
It's the same idea.
You would just be doing it on the steering box.
Put the tool on like that and then put your wrench on there and then pull and it breaks
it right free.
Okay, and this ends part one of this video.
If you want to see, obviously, reinstalling the Pitman arm go please to
part two.
We hope this helps you out.
Brought to you by www.1AAuto.com, your source for quality replacement parts and the best
service on the internet.
Feel free to call us toll free, 888-844 3393.
We're the company that's here for you on the internet and in person.
Thank you.