hello everyone! welcome to SweetieSembly, where I show you how to assemble your
baby products so you don't have to use the manual. Today I'm going to show you
how to assemble the Evenflo BabySuite DLX Playard. If you're new here and
these are the kinds of videos that you would like to see more of make sure to
subscribe and hit that bell button so you get notified. Ok now onto the video.
[Intro music plays]
So first we gotta make sure that we have all the items that we need.
Number one is the changer, two is the mattress pad, three is the toy bar, four
is the wheel assembly, there should be two wheels, five are the changer tubes
there should be three of them, six is the bassinet, seven is the soft console,
eight are the feet, there should be two feet, nine is the Playard.
The first step is to install the wheels onto the Playard
you take the wheel and as you see it has two grooves inside that line up with the
divids that are on the Playard itself. You take the wheel and you have to line it up with those divids.
And you slide it on
until you hear a click. And that's it.
Next you have to install the feet. What you do is, you see that it has a groove there
that matches up with the groove on the Playard. So what you do is, you slide it
onto that groove until you hear a click.
And then you do the same with the next foot.
slide it in until you hear a click. And there you go.
So next you have to open up the Playard.
What you do first is remove the mattress from the Playard by opening it up.
and then just putting it to the side
Then you pick up the Playard and stand it up. And separate the corners.
so that it opens up slightly like this
Then you have to lift up the rails, This is a bit tricky though, so what you do is
you have to feel for a lever that is under the rail and you press on that
lever while lifting the rail up until you hear a click and it locks in place.
Then you do that with the next longer rail; you press on the lever and lift up
until it locks into place. Once you're done with the longer rails then you have
to do the same thing with the shorter rails
Once again you feel for the lever that is under the rail, you press it and lift
up until it locks into place. You might have to try it a few times, you
might have to feel for the lever a few times until you can hear it and feel it
with your hands. Once that is done and all the four rails
are lifted up you have to separate the legs from the wheels and once those are
separated, press on the centre all the way down until its flat.
Then you take the mattress and you place it at the bottom of the Playard.
Then you have to take the velcro that are on the sides of the mattress and insert them
into the holes that are at the bottom of the Playard as you see here.
then at the bottom, you'll see that the velcro straps are sticking out.
There's velcro at the bottom of the Playard that you're supposed to stick that to.
So all you gotta do is take the velcro from the mattress and stick it to the velcro
that is at the bottom of the Playard.
So this is stage 1 of the Playard.
This is what it looks like for older kids.
Next, I'm going to show you how to install the bassinet and the changing pad.
to set up the bassinet you have to place it on the floor with the tubes and the sleeves facing up.
then you take the skinnier tube and you connect it into the fatter tube.
So next you have to install the bassinet onto the Playard. But first you have to remove the
mattress from the bottom of the Playard. So you do that first, unstick all of
the velcro and take it out and then put it to the side. Then you take the bassinet
and you have to press those four hooks onto the side of the short rails
then the four corners of the bassinet have velcro on them. You take the corners of the
bassinet and you stick them on to the wall of the Playard. You do that with
all four corners. Then each long side of the bassinet has a zipper on it so you
have to take the zipper and stick it onto the wall of the bassinet and then
zip it all the way up and then at the end of the zipper there is velcro so all
you do is stick that velcro on to the bassinet like so.
Then you have to put the mattress on the bassinet and secure it in place just like you did with the
bottom of the Playard the bassinet has six holes on the sides for the velcro that is
on the mattress to be inserted through. So all you do is insert the velcro
through those six holes and then stick the velcro to the bottom of the bassinet
just as you did with the bottom of the Playard.
next you have to set up the changer. You take one of the curved tubes and you
connect it to the straight tube like this. Make sure you hear a click, then you
have to slip the tubes into the changer
like so. Just gather up all of the fabric until it goes all the way through and on
the other side. Then you take the second curved tube and you have to connect it
to the other end of the straight tube, to do that you have to bunch up all of the
fabric of the changer until you can see the straight tube sticking out
then take the curved tube and connect it to the straight tube, to the other end of
the straight tube. Once you do that you just cover the tubes with the
fabric all the way down
and that's how you set up the changer
next you have to connect the changer to the Playard. So just place it on to the side
here. These hooks get pressed onto the sides of the Playard like so.
all you do is just press on them until they lock in.
and then this flap on the changer here, it's got two buttons that snap onto the side of the Playard.
next you'll see that there are straps on the sides of the changer. You just have
to connect those together on both sides.
To get the changer out of the way when it's not in use, you have to unhook the
straps that are on either side of the changer and then you can flip the
changer out of the way onto the side of the Playard.
Next you have to attach the soft console to the Playard. As you can see the console has two velcro straps
and the side of the Playard here has two holes, on the side here, so what you do is
you take the velcro straps and you insert it into those holes and then
attach it onto the console itself
you take the velcro strap slip it through the hole and attach it to itself
you unzip the top and as you can see it has all of these different pockets where
you can put diapers toys or clothes or anything that baby
needs. Then you zip it back up.
Next you have to attach the toy assembly to the Playard. To do that you have to straighten it out like so and then the
ends of the assembly, there are hooks, you just hook those ends to the sides of the
Playard here
next I'm gonna show you how to fold the assembly up and put it all away but
first to do that you have to take all of the pieces off the Playard first.
You have to pull up on the center of the Playard so that the wheels and the feet are now close
together. Then you have to feel for the lever on one of the long rails, press the
lever while pulling up on the rail and then push it all the way down. Then do
the same with the next long rail. Then once you have pushed both of the long
rails down you can do the same on the short rails. Once you've done that you
can gather up all the four corners until the Playard is folded up.
So folding up the Playard is a bit tricky. Sometimes the rails can lock even when
they're folded down like this. So what you have to do to fix this problem is feel
for the lever that is under the rail, press that lever and push down on
the rail
you place the mattress on the floor and you open it up. Then you take the Playard
and put it on the mattress. Next you take the bassinet and you unhook the tubes
from each other, you fold it up and put it on top of the Playard.
Next you take the changer and you have to unhook all three tubes. Put the three tubes on top
of the bassinet and then place the changer on top
last you take the toy assembly and you fold it up, you put it on top of the
changer then you take the mattress and you fold it over the Playard and you
take the other side and you bring it in
then you take the velcro straps and slip them through the hooks on the back of
the mattress and stick them onto themselves.
Then slip the carry bag over the Playard.
next you take the softcover and just like you did on the side of Playard.
The sides of the carry bag has two holes here, where you can slip the velcro
straps in and stick it onto itself
alright so that's how you assemble the Evenflo Playard. I hope that was really
useful for you. Once again if you want to see more videos like this make sure to
subscribe, hit that bell button and smash the like button too.
And as always make sure to let me know in the comment section below what other baby products you would
like for me to assemble next. That's all for today, thank you so much for watching
God bless and see you in the next video.
[end credit music plays]