Required Tools: Wire brush WD-40 spray All-purpose cleaning spray
Brake cleaner Copper grease Combination spanner #18 HEX bit no.H6.
HEX bit no.H7. Drive socket # 18 Wheel impact socket #17 Ratchet wrench
Torque wrench Tap wrench Hammer Impact screwdriver
Rubber mallet Crow bar Wheel chock
1. Raise the front of the car and secure on supports.
2. Unscrew the wheel bolts. Use wheel impact socket #17.
AUTODOC recommends: To avoid injury, hold up the wheel when unscrewing the bolts.
3. Remove the dust boot caps of the brake caliper guide pins. Use a crowbar.
4. Unscrew the brake caliper fastening.
Use HEX No.H7. Use a ratchet wrench.
5. Spread the brake pads. Use a crowbar.
6. Detach the brake caliper retaining spring. Use a crowbar.
7. Remove the brake caliper.
AUTODOC recommends: Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.
Make sure that the brake caliper is not hanging on the brake hose.
Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
8. Remove the brake pads.
9. Clean the brake caliper bracket fasteners.
Use a wire brush. Use WD-40 spray.
10. Unscrew the caliper bracket fastening.
Use a drive socket #18. Use a tap wrench.
11. Remove the caliper bracket
12. Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
13. Unscrew the brake disc fastening
Use HEX No.H6. Use an impact screwdriver.
14. Remove the brake disc.
AUTODOC recommends: If necessary, use a rubber mallet.
15. Clean the wheel hub fastener. Use a wire brush. Use WD-40 spray.
16. Unscrew the wheel hub axle nut. Use a combination spanner #18.
17. Remove the hub and the bearing together, since they are a sealed unit. Use a hammer.
18. Clean the hub bearing mounting seat.
Use a wire brush. Use all-purpose cleaning spray.
19. Install the new wheel hub with a bearing.
20. Tighten the hub. Use a drive socket #18.
Use a torque wrench. Tighten it to 70 Nm torque.
AUTODOC recommends: The wheel bearing unit must not tilt on the axle pin.
21. Treat the hub where it contacts the brake disk. Use copper grease.
22. Install the brake disc.
23. Tighten the brake disc fastening. Use HEX No.H6.
Use a torque wrench. Tighten it to 9 Nm torque.
24. Clean the brake caliper bracket from dirt and dust. Use a brake cleaner.
AUTODOC recommends: After applying the spray, wait a few minutes.
25. Install the brake caliper bracket
26. Tighten the brake caliper bracket Use a drive socket #18.
Use a torque wrench. Tighten it to 75 Nm torque.
27. Install the brake pads.
28. Install the brake caliper and fix it. Use HEX No.H7.
Use a torque wrench. Tighten it to 35 Nm torque.
29. Install the dust boot caps of the brake caliper guide pins.
30. Install the brake caliper retaining spring.
31. Treat the fasteners of the wheel hub bearing. Use copper grease.
32. Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
33. Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends: After applying the spray, wait a few minutes.
34. Screw in the wheel bolts. Use wheel impact socket #17.
AUTODOC recommends: To avoid injury, hold up the wheel when screwing in the fastening bolts.
35. Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17.
Use a torque wrench. Tighten it to 120 Nm torque.
AUTODOC recommends: Without starting the engine, press the brake pedal several times until you feel significant resistance.