Hey guys! How are you? Egar here welcoming you all with another video
we'll learn and see if we can repair this iPhone with Error 4013
but without disassembling it
How are you? I'm happy to have you here again
in this new video, and that's right, we'll try to recover this iPhone that shows an Error
what's the error? I have the iTunes open, let's click on Restore and wait a moment
and see where's the error
and see if we can recover it
Ok, here's, Error 4013
Ok then
this error is usually caused by a damaged Tristar
let's see if we can
check the Tristar
sorry, my tools are a bit messy
and sorry about the barks in the background
Let's see this
let's bring the Power Supply, and Flux is barking
sorry about that
this could even be the connector
Ok, let's see if we can connect this
let's connect it and now bring the Power Supply
these cables come from my Power Supply, set to 4 volts and 3 amps
ok then
touch positive with positive
and negative to measure, let's see
it was the other way around
here and
here
ok now let's try again
and start, Pin #1
You must be careful to not get confused with this, because the battery is charged, look at this
it seems to consume, but it goes down, don't be confused with this
if it didn't go down, then the problem could be the Tristar
but this goes down
starts to go down
ok, another and another, Tristar is fine
this error is usually caused by corrupted NAND memory
So, as we know, this P10 can enter "Programming Mode"
to our device
so we can put it in Purple mode and read the NAND memory
format it and see if that fixes the problem
I've always told you this tool
sometimes will get the job done
sorry if I'm looking around
sometimes the job gets done but sometimes it doesn't
Why? Because we must remember that
is only trying to enter in programming mode on the device
so, let's connect it
now it's connected
and connect the blue cable here
and now I'll connect
the phone
and it will recognize it in recovery mode
now it's in recovery mode, what are we going to do now?
Let's put it in DFU mode
press Power button + Home button
until it is turned off
and count, 1, 2, 3, 4, 5 and release the Power button while holding down the Home button
Ok, now it recognized it in DFU mode
let's press on DFU and see if this puts it in Purple mode
according to this, it is already in Purple mode
but I can't see anything here
and... I don't know
Ok, here's trying to read the NAND data
"Reading Hard disk information"
ok, it will try to read the NAND's data, let's see if it can do it
let's see
as you can see, it can't read it, it gets stuck there
the phone is supposed to be in DFU mode
but it can't read the data
and this is a problem you may have many times
this type of boxes won't do the job
so, here we have
to remove the NAND and try to read it with a NAND programmer
according to this it is in Purple mode
but if I click here, it doesn't read anything
look
it can't read anything
ok then
this box couldn't do the job
let's try one more time, I'll disconnect it
ok, now it's turning on again
ok, there's the message
I'll connect it and put it in DFU mode
1, 2, 3, 4,5 and release
ok, now it is in DFU mode, click on DFU so it can put it in Purple mode
ok, according to this
it should connect, but this simply won't work, so what are we going to do? Let's move here
let's remove this
put this aside
turn off the SMB, since we have already checked that the Tristar is ok
and we'll have to disassemble this
I wanted to make a video without disassembling it, but it won't be possible
Ok, what are we going to do? Let's try to remove the NAND
we can measure if there's a short
but it's not necessary, normally Error 4013 is due to the NAND
Ok then, here we have it, the NAND looks quite bad, I'm not going to lie
quite bad
and now let's see if
the JC can read it
in fact, I have one here, in case this doesn't work
I have a replacement
I'm going to put it here, yup it's 8GB
what's the capacity of this one? If it is 32GB
too bad, it's 16GB
Ok then, you saw this could read it
let's press Start
Okay, here we're going to extract the data
and press Save
already read it
already read it, 1BMR1DDMR
okay, that's the serial number
ok, now it read it, if we go to page 1, press on Save
and extract
this already saved G5QQ
that's the serial number
on page 1 press Format
is now formatted, now go to page 1
press Extract, it will show an error because the memory is formatted
it says "Failed", let's press on Save and Open, look for the backup we saved earlier and select it
and press to overwrite and Yes
now if we press on Extract
the data is there, so the NAND is ready, it's just a matter of formatting it
and put it back, now we have to repair it
we have to do reballing, but before that
we have to fix something there
ok then, let's see
this
we have to cover it with UV mask
we have to do that, cover everything
then reballing and then put it back
so, fast motion to the count of 1...2...3...
Ok!
We just finished, now I have
to pass to iTunes in the computer and
connect it again
it should be in DFU mode, there
click on Restore
and let's see if it's fine now
Ok, as you can see, now it's fixed
and now it's loading the software, now we have to wait and see if it can load the software
and see if there are no errors below so we just have to wait a little longer
Ok, there was no error
with our precious phone, click on OK
and close this, close this thing that didn't work
the thermal camera that I'm not using, we just need to open 3uTools
just to do something quick
ugh the phone is discharged
let's wait a moment for this to turn on
with the Power Supply
it discharged, so
I still have to assemble it, but I want to
ok, there
let's turn it on
turn on, perfect
now I'm going to connect it to 3uTools
connect it here
and wait a moment and see if 3uTools detects it
let's move to the computer
it charged here, I had put it there but I have a mess there
so, if we notice
here's the serial number J5QQ and only press here on Activate
and see that everything with the NAND is ok
that would give us the guideline that everything is perfect
Ok, let's wait a moment
there it is, is asking for iCloud, so this phone
is repaired, it is now finishing the start-up process
one thing I want to make clear is this
this many times won't do the job
there's when we need a REAL programmer
for NAND
I'm not saying this doesn't work, because it can often do the job
and save us from having to remove the NAND and go through the whole process
what I am saying is not to get complicated when we see that this doesn't read the NAND
it's just that it can't access to some NANDs
remember this enters to the phone via software
by "programming mode" in order to be able to
lauch all the commands and start working, but as we saw, in this model
we had to disassemble the phone, and remove it and read it
in the JC programmer
you can use any, I've always used the JC brand
Remember, the links of the tools I use will be in de video description
so this was an Error 4013, an error that's easy to fix
an error that most of the times the problem is the NAND, but always remember to measure Tristar
this phone is still charging, but we have already seen in 3uTools
the phone is on and there it is
it just need to charge
So it's time to say good bye, I hope you learned something today
don't forget to leave your like, comments and subscribe to the channel
because 70% or 80% of the people
who watch these videos are not subscribed, please subscribe so that we can learn a lot
Gentlemen, it was a pleasure, take care
and that's right, we'll see you in the next video
Bye!