1. Take out the device and accessories. (You'll find two radar shaping handles and hydro dermabrasion
handle are connected with the main machine and some screws on the machine.)
2. Replace any faulty fuse with one of the two spare fuses. Pry open the fuse cover with
the screwdriver, take out the faulty fuse and replace it with the spare fuse.
3. Replace any faulty film with one of the two black protective films of the radar shaping
probes. 4. Take out the screws and start to install
them. Aim the handle holder at the right place and twist the screws into the machine.
5. Install the round accessories hanging rack on two sides and an oxygen spray handle holder.
6. Place the 4.5MM radar shaping handle onto the handpiece holder.
7. Then place the 3.0MM radar shaping handle onto the handpiece holder.
8. Connect Ultrasound Handle with the device and tighten the screw.
9. Connect VANADIUM-TITANIUM handle with the device and tighten the screw.
10. Connect BIO Micro-electric Therapy Handle with the device and tighten the screw.
11. Connect RF Radio Frequency Handle with the device and tighten the screw.
12. Connect Ice Repair Handle with the device and tighten the screw.
13. Insert one end of the Oxygen Spray Handle wire into machine jack, then connect Oxygen
Spray Handle with the other end. Tighten the screw. Connect the spray bottle with the handle
and tighten the screw. 14. Connect the Sever-color Light Mask handle
with the device and tighten the screw. 15. Connect Vibration Massager Handle with
the device and tighten the screw. 16. Place all handles onto the handpiece holder.
17. The two bottles are clean bottles and waste bottles. The clean bottle is filled
with a hydro dermabrasion solution. 18. AS1 can be used for deep cleaning and
is suitable for oily skin, coarse skin, and congested skin.
SA2 can be used for deep cleaning and is suitable for all skin types.
AO3 is suitable for sensitive skin. Normal saline can be used to clean the device
and is suitable for sensitive skin. 19. Select the solution and pour it into the
clean bottle based on the customer's skin needs. Empty the clean bottle before switching
to another solution. 20. Twist open the clean bottle cover and
pour in solution. 21. Click the power button to turn on the
machine. 22. Then it goes to function interface. Working
time ranges from 0-60 min. The energy level ranges from 0-10. Adjust based on the customer’s
skin needs. 23. Click Bubble Brush. Adjust working time.
It is advised to treat 10 min or so. 24. There are altogether 8 Bubble Cleaner
tips to choose from based on different treatment sites.
25. Select one and install it onto the handpiece. 26. Click to start.
27. During Bubble Cleaner treatment, solution transfers to the skin and then to the waste
bottle as wastewater. When the waste bottle is full, the device will stop automatically.
So empty the waste bottle in time. 28. Twist the knob to adjust the suction level.
29. After the treatment, empty the waste bottle. Turn on the red valve to pass out the wastewater.
30. Fill in the clean water bottle with normal saline after each treatment. Turn on the device
and stop the handle with the thumb so the normal saline can circulate and clean the
device. 31. Soak the tips at 75-degree alcohol to
disinfect after each Bubble Cleaner treatment. 32. Click Oxygen Gun on the screen. Adjust
working time. It is advised to treat each treatment site for 10 min or so.
33. Take out the Oxygen Spray Handle. Fill in the bottle with water. (Choose from purified
water, watery essence, toner, normal saline, etc., based on skin needs.)
Twist the bottle back onto the handle and tighten the screw.
34. Click start. Twist the end of the Oxygen Spray Handle to adjust the level of mist.
Press down on the wrench to spray. 35. Click Ultrasonic on the screen. Adjust
the intensity level. It is advised to set between 3-8. and treat each site for 15 min
or so. Click start. The probe emits a blue LED. Ultrasound helps better lead to nutrients
and helps the skin absorb better. 36. Click Radio Frequency on the screen. Adjust
the intensity level. It is advised to set between 3-8 and treat each site for 15 min
or so. Click start. The probe emits a red LED. RF helps tighten skin, remove wrinkles,
and increase skin elasticity. 37. Click Ice Seal Imports on the screen.
Adjust the energy level. It is advised to set between 5-10 and treat each site for 10
min or so. Click start. Ice Repair Handle helps shrink pore and calm skin.
38. Click MicroPower on the screen. Adjust intensity. It is advised to set between 2-6
and treat each site for 10 min or so. Click start. The probe emits a green LED. BIO Micro-electric
Therapy Handle helps tighten skin, activate skin cells, and brighten skin.
39. Click VANADIUM TITANIUM on the screen. Adjust water output speed. It is advised to
set the speed between 3-6. (Higher speed means faster movement) and set the water inlet speed
between 3-6 (Larger flow means you’ll run out of essence sooner) and set working time
for around 20 min. 40. Then install the accessories. Firstly
install the microchip. 41. Then mount the positioner properly.
42. Click"go back" on the screen. The thruster will slowly push back. Mount the injector
properly. It can be filled with products like lyophilized powder/hyaluronic acid serum.
43. Click "go ahead" on the screen. The thruster will slowly push forward. It will stop when
it reaches the injector. 44. Click start.
45. Slide the control valve on the VANADIUM-TITANIUM handpiece to adjust the intensity. Slide up
to increase the intensity and down to decrease intensity. Higher intensity comes with a better
results. 46. Click Radar Lines 4.5mm on the screen.
(4.5MM acts on skin SMAS layer and can be used for skin tightening.)
47. It is advised to adjust the intensity between 5-9, output time between 0.8-1.5,
the interval between 0.3-1.0, and working time for 15 min or so on each site.
Click start then click pulse to start the treatment. Apply gel before treatment. You
might experience a slightly warm sensation. Higher intensity comes with stronger feelings.
Note: Use 4.5MM first, then 3.0MM to enhance the effect.
48. Click Radar Lines 3.0mm on the screen. (3.0MM acts on skin dermis layer can stimulate
the production of collagen fibers and elastic fibers.)
49. It is advised to adjust the intensity between 5-9, output time between 0.8-1.5,
the interval between 0.3-1.0, and working time for 15 min or so on each site.
Click start then click pulse to start the treatment.
50. Click Spectral Mask on the screen. Select color. There are 7 different lights of LED.
Select the LED-based on one's own skin needs. Select mode. There are two modes to choose
from. Adjust working time. It advised to treat for 15 min or so.
51. Click start. There are two modes to choose from: mono-color consecutive mode, 7-color
auto mode. Mono color consecutive mode targets specific
skin issues. 7-color auto mode can be used to improve skin
texture, soothe skin, and help skin absorb batter.
52. Take out the Vibration Massager. 53. Twist the knob on the left side of the
device to turn on the massager. 54. It starts to vibrate and emits red light.
55. When the Oxygen Spray Handle is blocked and there's no mist coming out of the nozzle.
56. Twist open the back cover, and take out the long spray needle inside, then insert
it back in. 57. Twist the screw back on. Push and pull
the spray needle. Back and forth several times to unclog the spray handle.
58. Twist the back cover back on and tighten it.
59. The spray should be able to work again.