What's up guys?
I'm Andy from 1AAuto.
In this video I'm going to show you how to replace the heater control mode switch on
this 2010 Toyota Rav4.
If you need parts for your vehicle click the link in the description and head over to 1AAuto.com.
Just take a trim tool.
We're going to take this piece of trim right off.
Just get underneath here with the plastic trim tool that way you don't scratch anything.
Slide it off then you can disconnect this connector right here and slide it off.
Just take a trim tool underneath here and just pop this up just like that.
There's clips on the back side.
On the backside right here there's a little tab.
Release the tab for the connector and disconnect it.
All right I'm going to take these bolts out and use a 10 millimeter socket extension and
a ratchet.
There's two on this side and two on the other side.
You might need a magnet, use a magnet to be able to grab them once they're loose.
Pull those up, pull that one out.
Now what you want to do is just grab the radio and just give it a little force.
Pop it out from the back side, disconnect the antenna, and then these other connectors.
There's a button on the bottom side of them, push down on the button and release the connector.
It's a little bit tricky to do this with one hand.
Slide that one, that one, and this one.
There we go.
There's the radio.
I'm just going to take a Phillips head screwdriver and take these two Phillips head screws out.
Don't lose them.
All right now let me just grab from underneath and up top and just pull it pretty hard.
And there's some connectors in the back, disconnect this connector right here just like that and
these connectors as well, the connector over here.
And then the one in the middle you might need a tool or a screwdriver to push down on the
button.
Let me just use my trim tool.
Push down, disconnect that.
And then, this is just popped off by accident.
Let's see.
All right.
So to disconnect ... Now this is for the heater controls.
Now it's got cables so you can just take a trim tool or a pocket screwdriver to get in
here.
There's a little release tab right there on that.
And then on the other side as well so release one side and then release the other side.
Just like that that pops off and the same with this one, just a release tab.
Hold it out a little bit and then push the release tab on this side.
It slides right out.
There you go.
I'm going to show you how to remove the mode switch for the HVAC system.
Flip this over.
I'm just going to put a little bit of pressure on the front of it while I take a pocket screwdriver.
There's a little clip right here, just pry that out and then also on this side a little
tab pry that out.
It slides right out.
All right.
Now we're going to double check to make sure we don't put this in upside down.
That's lined up.
It shouldn't go in upside down but just double check and lock it in place.
All right.
Take the panel and we want to plug all this stuff back in.
Now you can tell which side switch.
There's different slots on the back of these.
This side only has one slot that's right there and then the other side has two like that.
So let's plug this side in first and line this up.
You may have to turn the knob a little bit to get it to line up.
All right.
So slide that in and then you may have to turn this knob a little bit.
Keep in mind when you took it out you could put it in the same position as when you took
it out and that's good.
Just make sure that seems to be working properly which it is.
Plug this connector in right here and then the same with this one.
Slide this in position and just twist it on to get it to line up.
It looks good.
Make sure that it works and that's good.
We'll connect these other connectors.
This connector goes right here, the gray one, just lock that in place.
So the connector goes right here for the clock and then there's another connector that goes
over here to the heater controls in the AC switch.
Plug that in.
And we'll just line this up.
Now these go underneath here a little bit.
Just like that.
You line the holes up and then lock it back in place.
Now take a Phillips head screwdriver, we'll put these Phillips head screws in
right there.
Just snug them up and then one right there.
Not too tight because it is you're screwing into plastic so.
Now we're going to connect the connectors on the backside of the radio.
Now these connectors only go in one position so you just line up the connector with the
right position.
Those two go right there, the bigger one and the smaller one and then this blue one goes
right here.
And there is another connection port but we don't have another connector for that.
And then this one goes to the antenna, it goes over here, and line up.
I can slide this back in position.
Just watch out for those other wires on the side.
Once it's lined up just lock that in place.
Now we can take these bolts and I'll use the 10 millimeter socket and extension to get
these started.
We'll just get them all started first.
And you could use a magnet to get these back in if that helps you.
All right.
Those are all started and I'll just take a ratchet.
Just snug those all up.
Those are good.
I'm going to plug the hazard switch back in just like that and then line up these tabs.
Once it's all lined up just press it in.
Now we're going to connect this locking switch, line it up, and line up the tabs, and lock
it in.
Thanks for watching.
Visit 1AAuto.com for quality auto parts shipped to your door, the place for DIY auto repair.
And if you enjoyed this video please click the subscribe button.