Hey, DIY-ers.
This is Bryce from Alarm Grid.
And today we're going to be learning
about using your Honeywell Lyric controller with your garage
door opener.
The Honeywell Lyric controller is
compatible with your garage door opener
by using the 5877 garage door relay.
This garage door relay is compatible with normally open
and normally closed motors.
We recommend using 18 to 22 gauge wiring
when wiring your garage door motor to your garage door
relay.
When wiring the garage door relay,
you first must open up your garage door relay
and take one wire and place it on your common or your ground
terminal.
The next wire, depending on your motor, if it's normally
closed or normally open, you're going
to place it on normally open, or normally closed.
You will not hurt the relay if you place it
on the wrong terminal.
So you can test it out to be sure that it's on the right one
or it's working if you're not sure which motor that you have.
After you get that wired up, you can close it up
and get it closed up.
Or actually, you can let it hold off,
because you're going to actually need the serial number from it
later.
Next, you will take your 5822T, which
is the sensor that we recommend using
which your garage door opener, and programming it
into your Lyric.
This is a tilt sensor, so it shows
the best status of when your garage door is open or closed.
When it is like this, basically standing straight up,
the garage door is closed.
When the garage door opens, it lifts up, and it tilts back,
and it shows that it's open.
So to program this into your Lyric,
you're going to go to Security, Tools,
enter in the installer code, which is default 4112.
You're going to press Program.
Then you're going to press Zones.
And now this is where you must make sure
that you enter your 5822T on the right zone.
The 5822T has to go on either zone 127 through zone 130.
Garage door one is set for zone 127, garage door two, 128,
garage door three, 129, garage door four, 130.
So now when you go to Zones, you're
going to press the down button.
And we're going to get to 127.
Now 127, we're going to press there, and then Edit.
Then you're going to press the Serial Number field.
And now you can actually learn this device in.
So by learning a device in, you must activate the sensor
three times and the serial number goes in to the field.
So like I said earlier, it shows open and closed
by lifting it up and lifting it down--
[BEEPING]
--lifting it up, and lifting it down.
After every time, you should hear a beep
from your Lyric controller to show that that it's actually
picking up the sensor faulting.
So now, if you look onto the Lyric,
you'll see that the serial number is inserted actually
in the field.
So I have the serial number.
It put it in the correct loop number, loop three.
If I want to change the response type,
I can toggle through and change the response type.
But now I should just be able to press Save.
I can put my zone description right there.
And let's put garage--
let's actually backspace, let's get main out of there.
So we're going to back, garage--
I can't spell-- and there we go, Save.
And then once we save, that's in the system.
So now we can go back to the home screen.
Now that your 5822T is in this system--
it's programmed in the Lyric--
you now may get your 5877 garage door
relay ready to program in the actual Lyric as well, too.
So to program this, you may now go to automation.
So you'll actually press the Home button
one more time, Automation, press the Down button,
and then you'll see Garage Door Set-up.
At Garage Door Set-up, this is why I mentioned earlier
that you must remember where you placed the 5822T at.
The 5822T sensor was placed in zone 127, which
is set for garage door one.
Now you must put your garage door relay on garage door one.
Press Garage Door One, then Assign Device, and then you'll
press Serial Number.
Then you'll enter your serial number.
The serial number is right below the plug-in.
So ours right here is going to be 0018730.
018730, Done.
Perfect.
Now that we go back, you'll see that it
says garage door assigned.
You may now get your 5877 closed up.
Now your 5822T and your garage door relay
is set and ready to go.
These two items do come together in a pack
that we sell on our website.
It's called the 5877GDPK, which also
comes with a siren that shows you the lights to show you
if the garage door is open or closed when you're backing
in or out of your driveway.
If you find this video helpful, please
hit the like and subscribe button.
If you want more videos of when we do post more,
hit the notification button.
But it was a pleasure working with you guys today.
And if you need help or support, call us at 888-818-7728.
Or you can send an email to support@alarmgrid.com.
Have a good day.