Hi.
I'm Mike from 1A Auto.
We've been selling auto parts for over 30 years.
Hey, everyone.
Sue here from 1A Auto, and today we have a 2010 Nissan Murano in the shop.
We're going to be doing an oil change.
If you need any parts for your car click on the link below and head on over to 1aauto.com.
I like to take the oil fill cap off.
This assures me that there's no oil in the vehicle and not to start it if I happen to
walk away or someone comes over and looks under the hood.
Another thing I like to do is a quick visual before I raise the vehicle and go underneath.
Because if I see any fluid that's exceptionally low like power steering fluid or brake fluid,
what I'll do is look for leaks at that point.
If they look standard, regular fill, like the power steering is right at the max with
it cooled.
This car has been sitting and that's perfect.
Same with the coolant.
That's right at the level it should be with it cold.
And I'll check the fluid level.
It is right where it's supposed to be.
It seems to be good.
No low fluids.
I'll raise it up with my two post life.
The oil filter is located in the passenger fender well, so if you want to raise it up
you can take the flare plastic shield out of the way and expose the filter.
I'm going to put my filter wrench on there.
I've got a catch basin underneath it and I'm going to loosen it up.
Now with a 14 millimeter wrench or socket we're going to loosen up the drain plug on
the oil pull.
Line up your catch basin.
Here we have our drain plug for our Nissan Murano and someone has used a plastic washer
on it when the factory actually requires a copper crush washer.
This came from 1A Auto.
We stock them for Nissans.
That is a direct from the factory.
I'm going to cut this plastic washer off and replace it with the correct one.
Then this little plastic screwdriver.
You can see how it's not even working properly.
How it flared right over.
There we go.
Big difference.
And the way to install it, it just screws right on like a washer.
It's a one time use so every time you get a filter, which we stock, we stock the OE
factory Nissan filters at 1A.
You can also get the copper crush washer at the same time.
Now it comes time to fill the oil filter with fresh oil.
I call that priming the filter.
Take the cover off.
Grab the oil that you're going to use.
Before I install my new oil filter, I take a clean rag, and I'm going to clean the surface,
the mounting surface.
I want to make sure there's no debris or old oil there.
Sometimes dirt will fall on that spot.
The car engine can get dirty from the outside.
Road salt and sand, so I'm going to clean that surface.
Make sure there's nothing.
No debris.
Then I'll take my new filter, which I've primed.
And make sure your gasket--put some fresh oil, the clean oil on the gasket.
You might lose some oil when you tip it sideways if you've primed it.
For some engines the filter is straight up.
But this one is a sideways one, so some might drain out.
Once it bottoms out you're going to want to... it's snug now.
Now I know it's truly bottomed out.
I'm going to turn it about a half turn to a quarter turn.
Do not use an oil filter wrench.
I had the possibility of splicing the tin, and then your oil filter would be blown.
You can lose oil and blow your engine.
Now we're going to install the oil drain plug with the new gasket.
I always start it by hand.
And you'll see how that gasket bottoms out.
And now it's going to become a crushed washer so a 14 millimeter socket.
We're going to collapse that gasket and it will make a seat.
Once it's flush give it a quarter turn and you're done.
Always clean the area after you're done.
Now we're ready to add the oil.
This particular 2010 Murano with a V6 takes five quarts of 5 30.
Now with the oil in it and the oil cap securely tight I'm going to start it and run it for
about a minute and then shut it off.
Let it sit and check the oil level.
Now the car has settled for a little bit, so all the oil will go back to the pan and
I can pull the dipstick.
It's located right with the yellow handle.
You're going to bring it up.
Take a rag and clean it off.
I can tell you something a little bit about Nissans.
The way they design their dipsticks, it takes awhile for the oil to settle down on the stick.
The reading is always like crazy off the wall.
Sometimes you'll have one side way up here and the other side way down.
Before I dirty it up, you can kind of see the H right here and there's a little bit
of an L right there--so that's low and that's high.
We're looking to be right at the base.
There it is.
We want to be right about the base of the high.
Anywhere in the cross area is perfect.
You never want to be above the H. Too much oil is actually worse than low oil.
See what I meant?
If you flip it over here where the marks are not, it's pretty much indicating that it's
right there where it should be.
Flip it to the other side.
That would be right here.
But we have oil all the way up to here.
And that's just the way it is.
Now I let the car settle for a serious good 20 minutes so hopefully all the oil in the
dipstick tube is settled down.
We'll get a true reading.
Let's see what we got.
Yeah, it's right there.
It's right at the base of the cross.
Perfect.
Five quarts exactly.
Now that our oil change is done on our 2010 Murano, I'm going to reset the maintenance
light.
And that's as simple as keeping your foot off the brake and hitting the ignition button
twice and getting the dash to light up.
Once you do that, you go over to the side where it has your book menu, and you click
on this.
You see skip, alert, maintenance and options.
Go to the next level down.
There's a solid button.
Hit that until you see maintenance highlighted.
Then hit enter, which is the top book button again.
We're going to do oil filter and engine oil.
Then you're going to hit the black dot button and bring it over to engine oil.
Then hit the square entry book then hit the black dot for setting.
Then hit the square book, and you're going to hit enter, and now we can use the dot to
go for mileage and on this case we're going to go to 5,000 miles.
We'll go 5,500.
And I'm going to hit enter.
Let's do the oil filter.
Highlight the oil filter.
Do the same thing.
I'm going to go to 5,500.
Now you're all set.
Thanks for watching.
Visit us at 1aauto.com for quality auto parts, fast and free shipping and the best customer
service in the industry.