HP LaserJet Managed E8 Department Printer +6GW51A LaserJet Booklet Finisher Unboxing and Setup
This video will show how to unbox and set up the HP LaserJet Booklet Finisher on the HP LaserJet Managed E8 Department printer.
Begin by cutting and removing the shipping bands.Begin by cutting and removing the shipping bands.
Lift and remove the top of the cardboard box.
Remove the tray of accessories.
Cut along the edges on the bottom of the cardboard box and fold down the flap.
Remove the Styrofoam.
Carefully lift the finisher and slide it off the shipping pallet and onto its wheels.
CAUTION: The printer finisher is heavy.
Two people must lift and stand it up.
Remove the plastic bag.
Remove the blue tape from the side of the finisher.
Lift the top door and remove the blue tape.
Then close the top door.
Remove the blue tape and protective foam from the other side of the finisher.
Open the front door.
Remove the blue tape.
Close the front door.
Locate the accessories your removed earlier and remove them from the packaging.
Now you can prepare the finisher to be installed on the printer.
Press the power button to turn the printer off.
Then unplug the power cord from the wall outlet and remove any cables.
Locate the shipping bracket on the side of the finisher.
Remove the six screws that secure the shipping bracket to the finisher.
Rotate the bracket so that the back of the bracket lays flat on the base of the finisher.
Replace one screw to secure the bracket to the finisher.
Open the front door.
Using the handle, pull out the booklet maker.
Remove the blue tape and protective foam from the booklet maker.
Now you can install the booklet staple cartridge holders.
Insert the staple cartridge holders into the slots in the booklet maker and press down to lock them in place.
Push in the booklet maker.
Remove the blue tape, the shipping screw, and the caution label from the stapler.
Now you can install the remaining stapler cartridge holder.
Roate the green wheel to the left until the spring -loaded white tab is exposed under the stapler.
Then, rotate the green wheel to the right until the stapler moves back to the front position and stops
While holding the green wheel, insert the staple cartridge holder into the stapler.
Close the front door.
Locate the lower tray support brackets.
Insert the tabs on the lower tray support brackets into the slots on the finisher and lower them into place.
Install the two screws to secure the support bracket to the finisher.
NOTE: Four tabs on the tray snap onto the mounting brackets.
Screws are not required to secure the tray
Position the tray over the support brackets, and then lower it straight down to install it.
Pull out the tray extension and remove the blue tape.
Close the extension.
Next, insert the tabs on the upper tray into the slots in the finisher and lower the tray into position.
Pull out the tray extension and remove the blue tape.
Close the extension.
Next, insert the tabs on the standard booklet output tray into the slots in the finisher and lower the tray into position.
On the printer, slightly flex the turnaround bracket and remove it.
Locate paper settling guide bracket and the tabs that secure it.
Slide the bracket toward the front of printer to remove it.
Raise the bin-full actuator up almost 90 degrees away from the shaft.
Then rotate it towards the back of the printer until it snaps into the locking clip.
Remove the output tray cover.
Remove the two screw caps and screws that secure the output tray
Remove the two screws from the side power cover.
Then remove the cover.
Lift up and out to remove the output tray.
Replace the side power cover and then replace the two screws that secure it.
Next, slide in the intermediate paper transfer unit, or IPTU.
Remove the blue tape from the IPTU cable.
Peel off the cover label over the connector near the rear bracket.
Next, install the two rear brackets using four screws to secure them.
Position the finisher near the left side of the printer, and then connect two cables.
Open the finisher front door.
pull out the locking rail until it stops.
Align the brackets on the printer to the holes on the finisher, and then roll the finisher against the printer.
Push in the locking rail.
Close the front door.
Plug the power cord into a wall outlet.
The booklet finisher and printer are now ready for use.
Click the Playlists tab in YouTube to find HP videos in other languages.
And search our channel to find official HP Support videos.