hello and welcome to this video where
I'll be showing you how to install the
Whitestone dome glass screen protector
to the iPhone 10 our before we begin I'd
just like to point out that we do have
subtitles available on our video for the
regions seen here if you'd like to
enable this feature please select your
region from the settings below starting
with the installation now layout the
supplied installation tools and have
them ready to hand as there are quite a
few steps in this process in comparison
to other screen protectors once you have
everything prepared take a moment to
ensure the surface you're working on is
completely flat as even a slight incline
can result in the adhesive liquid
running off of the screen during the
installation process a great way to
check your surfaces flat is to place one
of the adhesive bottles down and see if
it rolls if it stays put then you're
good to go
but if it moves you'll need to find a
flat and level surface before you begin
with the ten are placed onto a level
surface use the cleaning wipe to
thoroughly clean the entirety of the
phone's display make sure you also clean
the edges thoroughly to ensure a perfect
base for the protector to be applied to
once you have given the display a
thorough clean use the microfiber cloth
to dry the screen before using the
District moogle stickers to dab away
like so this will remove any fine dust
or lint that may have fallen down onto
the screen during the cleaning process
with the screen fully prepared you can
now carefully place your phone into the
provided installation tray
making sure to position the top of the
10r to the bottom of the tray marked
speaker take the upper part of the
installation tray and put it into place
matching you up to the speaker text like
we did previously next peel back one of
the speaker covers and place it over the
ten our speaker this will stop the
adhesive from making contact white stone
also provide you with to absorption pads
that you can place either side of your
phone these just slot into place along
the sides and will take care of any
overspill from the adhesive gel once the
protector is applied it is recommended
to give the screen a final check with
the cleaning tools at the stage so you
can be certain you won't get any
annoying smudges or pieces of dust or
lint stuck under the screen protector
next position the plastic bridge into
the slots in the middle of the tray you
can now take the bottle of a deceive and
remove the different colored cap make
sure you take care to remove this one
first as
the black cap controls the release of
the adhesive with the cap removed screw
the bottle into the bridge like so don't
worry about any spillage as no liquid
can be released until you remove the
second cap which should be done once the
bottle is screwed into place unscrew the
second cap and allow the adhesive to run
on to the display it's recommended to
leave this for around 30 to 40 seconds
to ensure all of the liquid is out and
on to the phone
turn your attention now to the plastic
bridge and begin removing it from the
installation tray you'll need to take
extra care to ensure the adhesive stays
in place in the middle of your 10 ARS
display now we can turn our attention to
the protector itself remove the
protective film by pulling on the blue
tab taking care not to touch the
adhesive side with your fingers next
begin by aligning the protector by
dropping it into place starting with the
top of the protector closest to you
before lowering the bottom on to the
blue tab this will allow you to
correctly align the protector without
touching the adhesive bubble once you're
happy with alignment hold the bottom of
the tray lightly and take the side bar
in your over hand this will then slot
into place in the upper tray which will
allow you to hold it a 45 degree angle
and slowly push away from you to the end
line this action will cause the
protector to fall into place and allow
the adhesive to evenly spread throughout
the whole display it's recommended to
leave the adhesive to spread for around
80 seconds but you'll be able to see
when it's spread fully anyway you can
now use the UV light to kill the top and
bottom of the protector for around 15
seconds each once you're done with this
remove the upper section of the
installation tray like so before
removing the 10r
and giving it a quick wipe down next
place it on a flat surface and use the
UV light to kill the top and bottom of
the 10r for a further 60 seconds on each
side once you've finished the curing
process you'll be done with the
installation you can now enjoy using
your 10r with peace of mind that the
screen will be protected at all times as
with all white stone screen protectors
you'll instantly notice a superb fit and
a premium look and feel with no annoying
glue marks that can often be seen on
other screen protectors on first
impressions the fully clear appearance
looks fantastic the majority of other
glass screen protectors
to use a black lining around the bezels
of the phone to hide the glue whereas
the white stone dome bus doesn't need to
do this thanks to the high-tech
installation process I was really
curious to see how well the 10 are
performed with this screen protector and
after a little while I could barely tell
it was there the phone is just as
responsive as before meaning you can use
it just like you normally would with
flawless typing accuracy and perfect
touch position when playing games or
browsing the web it's also supremely
clear with just as much clarity as
before which makes watching videos and
playing games a truly enjoyable
experience in terms of case
compatibility I found this protected
does work with most cases with no issues
or limitations which is definitely
another bonus while installing this
protector may seem like a daunting
process I genuinely found extremely easy
by following the steps from this video
you'll be guaranteed of a well applied
screen protector that's easily the best
available on the market today it's a
little more expensive when compared to
other screen protectors but the unique
installation method really does insure
of a quality fit that's second to none
that's all we have for this installation
video if you have any questions then
please do leave them in the comments
below if you'd like more information or
to even purchase this screen protector
then I'll leave a link in the
description and comment of this video
[Music]
you
[Music]