These shapers are producing quality results in wood shops all over North America. After
almost 30 years selling shapers, we continue to provide our customers with the highest quality,
best performing shapers available today, and are the leaders in shaper sales. Let's get started
comparing these shapers by looking at the G0510Z 3/4 horsepower shaper. Shapers do much the same
work as routers. The main difference is that a shaper is a stationary machine designed for
larger work, using profiled shaper cutters, while a router is for handheld portable use with router
bits. The G0510Z features a strong 3/4 horsepower, 110 volt, single-phase motor. The power is
transferred from the motor to the cutter head by a flat belt drive. This shaper incorporates
an on/off toggle switch. the G0510Z has a spindle that turns at 8,900 RPM. The fences are
independently adjustable. And the machine features an over-the-cutter see-through guard. This shaper
features a miter slot with an adjustable miter gauge. The spindle of this machine is reversible
by the simple flip of a switch, which is necessary to perform some cuts. The spindle is height
adjustable and locks securely in place. the G0510Z has a cast iron table that is 17 and 3/4 of an
inch wide, and 15 and 5/8 inches deep. The G0510Z is also capable of handling both 1/4 and 1/2 inch
shank router bits, and comes with the router bit adapter and collets. Conversion for the use of
router bits is relatively simple. First, make sure that the power is disconnected from the machine.
Remove the spindle lock nut, and any cutter or rub collars that are installed on the spindle. Loosen
and remove the taper nut while holding the top of the spindle with a wrench. Gently tap the bottom
of the drawbar to knock the spindle loose. Remove the spindle and drawbar assembly from the spindle
cartridge. Place the desired collet into the collet nut by pushing it in until it snaps. Insert
the collet into the spindle cartridge and insert the router bit. Finally, tighten the collet with a
wrench. The preformed steel stand of the G0510Z provides great stability. This shaper weighs
one hundred and sixty seven pounds, so it can be portable for on-site use. To see all the available
accessories for this shaper visit the G0510Z page on our website, grizzly.com. The G0510Z ships in
one sturdy cardboard box and it measures twenty six inches long 20 inches wide and 24 inches tall.
The box weighs in at a 172 pounds, so please ask our operators about the lift gate services
offered. Next we will look at the G1035 and G1035P 1 and 1/2 horsepower shapers. The G1035 and G1035P
shapers are exactly the same machine, except for the color. They feature a strong 1 and 1/2
horsepower motor that is pre-wired for 110 volt operation. However, these shapers can be rewired
for 220 volt operation. These shapers incorporate a forward/reverse switch that can be padlocked for
security and to prevent unauthorized use. They have a solid preformed steel cabinet for added
stability and come with 1/2 and 3/4 inch spindles. You have two speeds of 7000 rpm and 10,000 rpm to
operate the spindle at by changing the location of the drive belt. These shapers feature a split
adjustable rear fence. And a cast iron table that measures twenty and one-quarter inches wide by 18
inches deep. We also offer a table extension as an optional accessory to increase the table
depth to 28 inches. the G1035 can use a variety of shaper cutters with either 1/2 or 3/4 inch
bore. These shapers have three inches of spindle travel. For added safety, we provide safety hold
downs and a cast iron over-cutter guard. the G1035 and G1035P also have a straight miter gauge slot,
and include a heavy duty miter gauge. The G1035 ships in one sturdy cardboard box,
and it measures 24 inches long 22 inches wide and 42 inches tall. The box weighs in at 221 pounds
so please ask our operators about the lift gate services offered. Next, we are going to look at
our very popular three horsepower shaper, the G1026. The G1026 shaper has a three horsepower
motor, 220 volts single-phase power, with the spindle-reversing switch. The forward/reverse
switch allows you to reverse the direction of the spindle for certain shaper cutters. Plenty of
power for your toughest shaping jobs. The shaper incorporates a magnetic safety switch for overload
and power failure protection. Power is transferred from the motor to the spindle by a V-belt drive,
and has two spindle speed settings of 7,000 and 10,000 rpm. Both spindle cartridge and motor have
high-quality ball bearings that are shielded and lubricated for life. The solid cast iron
table is 28 and 1/4 inches wide by 30 and 1/2 inches deep with the included extension wing
installed. The table is precision-ground to a mirror-like finish smooth lumber feeding. the
G1026 offers a 1/2 inch, three-quarter inch, and one-inch spindle to allow for use of the
widest range of cutters available. There is an optional taller spindle available for using up
to three inch tall cutters. The table has spindle openings of one and one-quarter inch, three inch,
4 inch, and 7 inches in diameter. The G1026 has three inches of spindle height adjustment. The
G1026 offers an independently adjustable split fence. A heavy-duty miter gauge and sturdy spring
hold-downs to assist in producing a consistent smooth cut. We offer an incredible variety of
standard grade carbide shaper cutter profiles, including style and rail sets, panel cutters,
and under cutters, as well as our ultimate quality 5-wing micro grain carbide shaper cutters. The
G1026 ships in one sturdy reinforced box and it measures 31 inches long, 26 inches wide,
and 41 inches tall. The box weigh is 392 pounds, so please ask our operators about the lift gate
services offered. All of the shapers discussed today have powder coated paint to ensure a tough
scratch-resistant long-lasting finish, and have been designed to provide the best in features
and maximum performance and value. We stock all of these models at all three locations in
Pennsylvania, Missouri, and Washington, and 99% of the orders are shipped the same day. We maintain a
huge parts warehouse and keep over a million parts in stock for our machines. Just call our toll-free
number 1-800-523-4777. You can order these, or review detailed specifications and manuals,
on our website grizzly.com. Thank you for your interest, and we look forward to serving you soon.