Hi, DIY-ers.
Joe from AlarmGrid.
And today, we're going to show you
how to wire motion detectors to the panel.
We're also going to show you how to connect two motion
detectors to the same zone.
Now, this is two-wired motion detectors on one zone.
This is a useful technique that you can use.
It works on just about any wire alarm system.
And the reason that it's useful is
that you can have two separate motion detectors.
They'll both work as alarm zones,
and they connect and only occupy one zone on your system.
The downside to this is that if either motion detector
triggers, it's not going to tell you specifically
which motion detector went off.
So you won't have that fine-grained information
about exactly which motion detector triggered the zone,
but you can save a zone by attaching two or more motion
detectors to one zone.
So let's show you how to wire up the motion
detector in the first place, and then we're
going to join it to another motion detector
and have it all go back to the one zone.
So we have a VISTA-21iP panel right here
and we've taken most the wires off to make it really simple
and so that you can see where we're
going to make our connections.
And I have this wire set up for later but if you can see,
we have a four-wire connector right here.
We have the black and the red on a 12-volt power.
And then we have the yellow wire on the zone 1 plus.
Now, if we're going to just connect one motion detector,
I'm going to connect the other zone wire to the Z1 minus.
And this is the first zone on the panel.
So I'm just going to screw this in.
And then at the motion itself, this
is the DSC LC-151 motion detector.
This is a front plate on it.
I've taken it off because we have to get to the terminals.
So in this motion, we actually have
a port where we can insert the wires from the back and to,
so I'm just going to slip this through.
And we're good to go.
And you're going to want to make sure that everything is off
before you do this as you will be working with the power
connection for the motion and you
don't want to short anything.
Our system is fully powered down.
So now the wires in here.
So if I only wanted to connect this one motion,
you can see we have plus-12 volt and a minus-12 volt.
So that would be our power connection.
So I'll just throw these wires in real quick.
Then if we wanted this is the only motion
on this particular zone, we would just
have to wire one of these to the common and one
to the normally closed.
So I'm going to put the green on the common,
and the yellows on the normally closed.
And now, we have our single motion detector connected.
You can add a resistor to this motion
in the line on the zone wires if you want to supervise it.
But for most single device security installations,
you don't have to worry about that.
We are going to add a resistor onto our second motion
when we connect that.
It's always a good idea to add a resistor on your zonal loop
when you're doing two motions on a one zone
because there's more than one device on the zone
and you're going to want to know if something
happens with the wiring.
So to prepare for our second motion,
we're going to have to remove one of these wires.
And as you can see, we have our green on our Z1-minus.
And again, this doesn't really matter right now because it's
just a zone terminal, so the polarity,
it doesn't have anything to do with power.
Well, let's just keep continuity going
throughout the whole loop.
So if we have our zoom in on our minus,
I'm going to undo our yellow from the Z1-plus.
So now, when the zone connection comes back
from our second motion, it's actually
going to land on this first zone terminal.
So in our motion detector as we've disconnected the yellow,
let's disconnect the yellow from here.
So we just have our green wire connected
to the common on the motion and to the Z1-minus on our panel.
So now we have to take one wire from this motion
and get it over to the second motion.
We have another DSC motion right here.
This guy's called the Encore EC-301.
It's not a wired motion.
I've taken the cover off so that we can go to our terminals.
So I have another wire setup right here.
I'm going to take this guy, I'll slip it through this port,
and I'm going to connect this wire
to our normally closed wire that we took the other wire off of.
Seal it tight.
Great, so now this motion is pretty much all set.
So I'm going to put this guy down,
I'm going to come over to our second motion.
Now when you have a second motion,
it will need to get power from the panel somehow.
What I've done is I've actually made another power whip
right here for this second motion
just to show that we're going to connect it.
If you can't get a wire back to the panel itself,
you can always jump off of the other motion to get your power,
just so you know.
So let me insert this in the back.
And I'll make my power connection.
I can see I have a 12-volt and a GND.
So the 12-volt is going to be the positive
and the GND is going to be the negative.
So I actually was able to get pulled the wires in both
at the terminals, just going to tighten it down.
Now, as this is the second motion,
we have to connect the wire from the normally closed
on our first motion, and then we're
going to have to connect the wire from this motion
back to our panel, back to our open zone terminal.
So let me slip the wire from the first motion in this guy,
and this is coming from the normally closed.
I'm to connect this to the common.
And then from this motion, I have another wire set up.
And on this one, I've installed a 2K resistor in line
so that this whole loop throughout our motions
will be supervised.
If anything happens to the wiring connections
on these motions, the system's going
to see that the resistance got interrupted
and it's going to tell me that there's
an issue, which is again, is very helpful when you're doing
these sort of setups that have more than one device
because you're going to want to know if something goes wrong.
So this one, I'm going to slip this in through the back.
And I'm going to connect this wire to our normally closed.
Wire connections are tight.
Then over here, we're going to take--
I've attached the resistor to our wire
with a dolphin connector.
These are really good to use you just twist the wires together,
slip it in, crimp it, and then it gives you
a nice secure connection.
I'm going to insert this in the zone 1,
and then we can pop our covers back on.
Then we would have to program to make them work as we want,
but we have them both wired up and ready to go.
Now on this system, after we program it,
these two motions are going to both function on the same zone.
So they'll both be able to trigger an alarm.
But if one of them goes off, we won't know which one actually
triggered as they're both going back
to the same zone terminals.
As a side note, whenever you do install devices
like this or devices in general that have a resistor,
it is a recommended practice to put the resistor
at the device that's furthest away from the panel.
This will give you true supervision
of the wiring for that zone.
Reason being, wherever you put that resistor, that's
how far the supervision goes.
So if we install the resistor on the terminals on the panel,
we won't know if something happens to the wire
integrity on the line.
If we put the resistor where the device is,
that resistance is going to be on the whole line
all the way back to the panel.
And if anything happens that wire,
that'll tell us that there's a trouble with that zone.
So if we go and look at our stuff over here,
we have our two motion detectors.
Let's say that this motion is the one that's furthest away
from the panel, and this is the one
that we want to use then to supervise our wires back
to the panel.
All you have to do to do this is take off
one of the legs of the zone wiring,
pop it out, take your resistor, splice it off,
and then ideally, you want to use a B-connector or some kind
of secure connector to really make
that connection nice and tight.
Crimp it down.
Now our resistor is attached very securely.
Fold the wires so they fit in your motion,
and then take your other leg of the resistor,
and we're going to slip that into the terminal for the zone
where we took the other wire out of.
If you do this when you first install the motion,
you don't have to remove the wires
and go through the headache that I'm going through.
So that's the recommended way to do it.
But either way, it works.
Now the resistor at the motion that's
furthest away from the panel, we're
going to have supervision from that motion
all the way back to the panel, which is the best
way to install a resistor.
A lot of times, you may find that it's just not convenient
or that you're not able to get to that device.
Remember, the device is made, doesn't really
fit resistor easily.
If you do put it on the panel, it will work.
Just know that that supervision isn't
going to be supervising the whole line.
That's how you wire a motion detector to your wired alarm
system and how you connect a second one in series
so you can have two motions on zone terminal.
If you have any questions about this process,
give us a call at 888-818-7728.
Head over to our website, www.alarmgrid.com or send us
an email to support@alarmgrid.com.
If you like the video, feel free to subscribe.
And if you want to be notified when we post future videos,
hit the notification button below,
and we'll send you an update when we do so.
Thanks for watching and have a great day.