Hey friends, it's Len here at 1A Auto.
Today, I'm working on a 2015 Chevy Equinox.
I'm going to be removing the front bumper cover.
Going to be a very easy job.
I want to be the guy that shows you how to do it.
If you need any parts, you can always check us out at 1AAuto.com.
Thanks.
Okay, so what we're going to do is we're going to try to get this little plastic plate off
of here.
There's some push clips.
I'm going to go ahead and remove these.
The center of these pulls up from the outer part of it.
I'll show you what it looks like here.
That's what they look like.
When you have the center pushed in, it forces those two sides out, which holds it in the
hole, okay?
That's why you lift up the center part, it relieves pressure and this thing can squish,
slides right out of the hole, okay?
We're going to do the same thing for all of these.
Just a little spot you can try to get your tool into, using my little forky tool.
You can use whatever you've got.
A flathead screwdriver usually works pretty well.
Let's set these aside.
Sometimes they come apart, that's okay.
We'll just shove it back together.
Easy peasy.
Okay, so we've got those four out.
Let's see if I can grab this plastic.
Wiggle it around, see what's holding it in.
Now that we've got this side off, we're going to do the same to the other side of the vehicle
and then we'll go ahead and we'll start removing the rest of these bumper cover.
Here we go, that one out of the way.
Now we're going to remove these.
These are Torx bits.
Little T20s.
Okay, like little stars.
This is what the tool looks like.
Put it in here, turn it to the left, zip them all out.
I'm going to leave one in, just going to have it loose though.
That's just going to make it so the bumper cover stays on while we continue down at the
bottom there and it'll hold it up for us.
That's what those look like.
They're all the same, except for the one that's still there of course.
This can move around a little bit.
Perfect.
Let's move along.
We're going to do some push clips here.
We got a push clip right there.
There's going to be another one right in front of this tire, right there.
Here, and here.
After we remove those, there's a T20 and a T20 there, the same tool we used up top, we're
going to use down bottom.
Okay, so I got my little forky tool, I got a little pocket screwdriver.
Just going to see about trying to pull up the centers of these push clips.
I showed you how they worked already.
Show you again just in case.
When it was closed it was like that, those go in between, pull out the center and then
it unlocks the little edges there.
Here we go, we have that one, move down the line, grab this guy.
This one's going to be a little harder to get to because of the tire but I'm sure it
can be done.
Okay, got our push clips, we'll set those aside.
Got our T20 here, here.
They both look the same.
Easy peasy.
Can't mix them up.
It feels pretty great.
Take a peek under here.
We've got that bolt right there.
I'm going to grab the size for that real quick, I'll let you know what it is.
Once we get that out, we're going to do the same exact thing for the other side of the
vehicle, and then we'll lift it up more and we'll grab everything from underneath.
All right, so we got our seven millimeter, so blast this out of here.
There it is.
Set that aside.
Okay, give that a little tug.
Perfect, so now like I said, we're going to do the same exact thing on the other side
of the vehicle.
We'll raise it up, we'll continue on releasing the rest of this bumper cover, disconnect
the fog lights of course, and then we should be clear to bring it back down and pop it
all right off.
Under here, we've got our fog light assemblies.
You can see it from the back side.
We've got some wiring that goes to the bulb.
We're just going to turn the bulb to the left counter-clockwise until it stops, and then
we're going to carefully pull it out, see?
We'll give it a quick inspection.
We've got our rubber seal there, slide it back over, it's easy enough.
Should be easy enough without the flashlight in my hand.
There it is, cool.
All right, so something to note, you want to be very careful not to touch on that glass,
especially if you've got oily hands or anything like that, even gloves isn't really the best
to touch the glass, so if you can avoid it, that's always great.
Take a look, see if it looks like it's black in any way or discolored or swollen or the
filament inside looks like it's got any crusty buildups on it.
If that was the case, you'd want to replace it and right on the back of the bulb, you
could see what the bulb number is, it's an H11 on this particular vehicle, so I'm sure
it is on your vehicle as well if you're working on the same thing.
I'm just going to leave this down to dangle.
That's a funny word but anyway, we're going to leave it so it can hang like that and I'm
going to do the same to the other side and then we'll just go ahead and we'll remove
a couple more bolts here, get the lower part of this thing moving, and then we'll go ahead
back up top, we'll take off the last bolt and we should be able to slide this right
off.
Here we go.
This part right here is part of the inner wheel well that we were taking apart up there,
so we want to remove these two bolts.
We're going to continue with our seven millimeter.
Turn these to the left obviously.
Come right along.
This little electric tool is amazing.
Slides out, clear to come off.
Feel a little triangle here, okay?
When you pull it off, you can see.
That just means when you're putting it back together, that triangle's going to go back
under there, okay?
Just holds it, and you can put your bolts back in.
Easy peasy.
Okay, cool, so this is wobbling around pretty easily now.
I would say we're clear to bring it back down and we'll start pulling it off.
Here we go, time for our last bolt up top here.
We're going to pull that bumper cover, make sure it doesn't want to come loose too much
on us until we can figure out exactly what's going on.
Now don't forget, we have our fog lamp bulbs just hanging under there, okay, so the less
that we jiggle this around, probably the better overall.
Let's see if I can get this off.
There we are.
Now we've removed out front bumper cover.
Here we go, we've got our bumper cover.
We're going to lift it up on here.
We're going to be careful of these edges to make sure they don't go hitting up against
the fender.
This one's a little damaged but that wasn't my by the way.
Just playing, it really wasn't though.
I'm just going to keep those edges low and I'm just going to scoop the top in up here,
just get it kind of settled in.
I'm going to start a couple of these bolts just to hold it for me, and then I'm going
to work my way along the edges there.
Get everything settled in along the top, and then I'll go down to the bottom and do the
same thing.
What size is this?
Twenty.
Torx bit 20.
We'll keep it loose just in case we have to move some stuff around, right?
Just want to make sure that it can't fall down, hit the floor.
Like I said, I'm keeping all these loose, I'm just starting them in so I can move everything
around as I need to, okay?
Nice and loose.
Okay, let's come along here.
Right up along the headlamp, we have the little scoops, right?
You come over here, you got a little clip, clip, clip, clip, clip, okay, so that's where
your bumper's going to want to ride in, so you're going to need to bring it up, bring
it right up along your headlamp.
The bumper cover itself has all these little slots in it, that's where those clips are
going to want to ride.
You're probably going to need to give it a little tug just to get it into where it needs
to go.
All right, looking good.
I'm going to do the same thing to the other side.
All right, so we've got the bumper all lined up.
It looks great.
Couldn't ask for better really.
I'm just going to take my Torx bit 20, snug these puppies up.
Very nice.
All right, now let's lift it up to a working height so we can get to those wheel wells.
We'll get all those put together, then we'll bring it all the way up, we'll plug in our
fog lights and finish up along the bottom.
All right, so we remember that we had the one seven millimeter head bolt, goes right
up through here, right?
Goes through the bottom of the bumper cover up into the fender.
Just use my little tool, you can use a ratchet, whatever you've got.
We're just going to find the hole here.
There it is.
Nice and snug.
We'll grab this, slide it back into position here.
Okay, so now when we look at it, you can see behind there, there's a metal piece, that's
where there's a screw.
This one's just a big gaping hole, that's a plug, screw, hole, hole, hole.
Let's see what we got for parts.
We got two screws, perfect.
I remember saying we needed two screws.
We got four little push clips.
We didn't lose anything.
We're doing all right.
Here we are.
Let's do the push clips first because they'll kind of keep everything kind of generally
speaking where it should be, right?
Then we can worry about putting in all those screws after.
Here we go.
Two screws.
I'm just going to grab my little Torx bit, I got it right here.
Sticking with my 20.
Turn the wheel, or not.
See if I can get this in.
I'm going to grab a ratchet, I'll finish that one off in one second.
Here we are.
Okay, grab my ratchet.
Feels great.
Okay, all those are still in.
Perfect, we'll do the same to the other wheel well and then we'll bring it up and continue.
Now we're gong to put in our fog lamps.
Once again, we're going to be very careful not to touch that glass, okay?
We'll just check them one more time to make sure the filament's not broken.
We did a lot of moving around.
I'm just going to take it clean up in here, I'm going to start by going all the way as
far counter-clockwise as I can and then I'm going to turn it to the right so it locks
in.
Should be straight up and down in the locked in position.
I'll come over, we'll do the same thing over here.
Check it.
Looks pretty great.
Filament's not broken, nothing moving around.
I didn't touch the glass.
I'm going to bring it over, I'm going to turn it all the way counter-clockwise as far as
I can until it grabs, then I'm going to bring it back to the right.
Once it sets in, we'll bring it down.
It's locked.
It's in the straight up and down position.
All ears are in.
Cool.
Now we're going to grab this.
We got our little triangle ear here.
It's going to slide over that just like this.
Sets in.
We're going to do the same thing to the other side.
We've got two bolts.
Easy peasy.
All right, so I've got my bolts.
I'm just going to take them and I'm just going to put them in.
All right, this one.
Right here.
This one.
Very nice.
Everything feels great.
We'll bring it back down, we'll finish up with the top and we should be all done.
Okay, so now it's time to put these up along the top.
Got our little clips here.
Like I said, if you looked at this and you didn't see the metal clip, it's probably inside
these holes right here.
If that was the case, you'd want to just take them out, okay?
You can use something like a pocket screwdriver or whatever you have to do.
Get them out of there, put them back on this.
You can't just go ahead and put this plastic into those metal clips if they're down there.
They just don't like to work that way.
We're going to line up these with these holes.
Being careful not to scratch any of our paint just like always, we're trying real hard to
do a good job here.
That slides under there.
This up here.
Got our holes lined up.
Just give it a little bonk, bonk, bonk.
That slid in there.
Okay, we've got four push clips.
One here, one there, here, and there.
You can do them in any order.
You do you boo-boo.
Slide them in.
Then push in the center.
Slide it in, push in the center.
Onto the last, slide it in, push in the center.
This under here should go right in there.
Very nice.
Okay, let me get this puppy lined up.
There's just a little hole in it right there, that slides over this, okay?
It's just kind of like a rain drip guard type of deal.
There we are.
Looks pretty great.
We'll do the same to the other side, and then we're all set.
Thanks for watching.
Visit 1AAuto.com, your place for DIY auto repairs for great parts, great service and
more content.