hey guys drew from geoarm here again to talk to you about the mno2-lte from m2m and its connection
to the honeywell vista 20p for both communications and interactive this also applies to the vista 15p
uh the there's a few other models but specifically the vista series
if you are wiring for communications and for interactive this is your video so uh
go ahead and get your m2m mno2-lte and uh get it connected to its antenna like so here
screw it right on to the connection here that's ready to rock now uh as you can see
the antenna is magnetized so you can set it outside the box or you can put it inside the
box top of the box wherever you want to put it uh just make sure that uh you have it connected
now what we're going to do here is we're going to go ahead and get this connected prior to
doing this make sure to power down your security system entirely backup battery and power supply
just go ahead and do that just to avoid anything happening nothing is going to happen to you
by the way it's very low voltage but it could definitely fry the panel uh so we're going to
go ahead and get this wired in for power first so we're going to be going to terminals four and five
here terminals four and five uh respectively ground or aux minus i'm sorry and aux plus
on five uh were uh are gonna already have wires in them uh more than likely keypads
or zone expanders or whatever else the case may be uh that is uh needing to utilize aux power
so we're going to take the black wire the black wire is going to be wiring into
aux minus which is terminal number four and then you're going to go ahead and get that screwed down
now there's going to be other wires in there as i said go ahead and put this in there along with it
make sure to screw it down tight make sure all the other connections are still made in there
nothing slips out now we're going to take the red wire we're going to get that into
terminal number five like so super easy to do you just slide it underneath the little plate here
that the screw has if it doesn't have a plate just kind of get it wrapped around the screw and then
get the screw tightened down now what we're going to do is we're going to wire in for communications
which is going to be the yellow and green wire so we're going to take the
uh the green wire and we're going to wire that one to terminal 24 like so
so green to 24 which is ring and then we're going to take the yellow wire and that is going to be
going to 23 which is tip now if these terminals 21 22 23 and 24 on the vista panels have wires
going into them currently for phone so t1 r1 tip and ring if those four terminals have anything in
them take the wires out of there because this is the only thing that needs to be connected
at this point now we're going to go ahead and wire it for the interactive application
you're going to take the white wire the white wire is going to be going to terminal number
six there probably are going to be some green wires or something similar like that
in this slot already as i said don't remove those just screw this down in there along with it
number seven is going to be the orange wire you're just going to take that
and put that in there if there's wires in seven which there will be don't take them
out just put this in there along with it at this point all connections from the m2m have been made
we have power which is red and black we have the data connection for interactive which is here six
and seven which is the white and orange wire then we have the communications at tip and ring here 23
and 24 which is the yellow and green wire at this point you're ready to get your m2m activated for
communications and for the interactive app we're going to need you to give us the serial number
which is located right on the top it's a six digit number also do not forget when you get this device
you're going to get a manual and in this manual is going to have your username and your password
to get logged into the rcontrol app do not forget to document this save this this has also got other
helpful bits of information on getting this thing wired in back fed et cetera through the panel
and of course if you have any questions go ahead and feel free to leave a message
down below and we will get right back with you um thank you guys for uh watching this video
uh once again this is how to wire the honeywell vista uh with the m2m for both communications and
the interactive app take care guys make sure to subscribe to our youtube page and click the
show more tab underneath the video where you can view valuable links pertaining to this product
similar how-to videos and our low-cost no contract alarm monitoring services