Rebuilding a Value Series Linear Actuator can be a little tricky, so we’re going to
quickly walk through the process step by step.
All you need is a set of metric and imperial Allen wrenches, possibly a 12mm wrench and
the appropriate re-build kit.
I’m using this slide, which has a point 5 pitch on the lead screw, so I need this
rebuild kit which is for the point 5 pitch value series slides.
It has lubricant, new bearings, a new lead screw nut and a new set of liners.
There’s another kit for the Value series slides with a point 2 pitch lead screw.
These instructions are the same for any length slide; I’m using this short 6 inch slide
for the demo because it is easier to fit on the video screen.
Here we go.
Loosen the shaft coupler on the Linear Slide side – not the motor side – remove the
four motor screws and remove the motor, coupler and adapter plate.
Loosen the set screw on the lead screws lock nut – don’t take the screw out, just loosen
it a little bit.
You can usually remove the lock nut by hand, but if it is tight, use a 12 mm wrench to
loosen it.
If you need to use a wrench, then go ahead and take one of the motor mount legs off to
make the nut easier to reach.
To get more torque, just move the carriage to the far end plate – that will lock the
lead screw in place and make the nut easier to get off.
Remove the screws holding the lead screw in, remove the motor end plate, and pull the leadscrew
out.
Remove the other end plate.
Loosen the pre-load screws on the carriage – don’t take them all the way out, we
don’t want the carriage to come apart, remove the carriage and replace all four liners.
When you put the new ones in, there is a raised ring that sits in a groove on the carriage.
Make sure that’s seated.
Slide the carriage back onto the rails making sure this tab is on the same side as the proximity
sensor mounts and also making sure the new liners are seated.
If you have trouble getting it on, loosen these pre-load screws a little bit more.
Once the carriage is on, lubricate the rails.
There is a spring in the bottle you can use to help mix up the lubricant in case there
was any settling.
Apply a little lubricant to the rails and slide the carriage back and forth to help
evenly spread the lubricant.
There should be a thin even layer of lubricant on the rails.
If not, add some more and move the slide around to distribute it.
Tighten the preload screws until you feel a slight resistance.
Adjust the screws until the carriage can be pushed with light effort.
It shouldn’t move freely on its own.
Replace the motor mount bearings with new ones and replace the bearing on the lead screw.
I use the lead screw nut to push that last bearing off the lead screw and remove the
lead screw nut at the same time.
Replace the lead screw nut and bearing.
Make sure the triangle flange faces the motor end of the leadscrew and move the nut up the
screw a little ways.
Insert the leadscrew into the motor mounting plate.
Add the lock nut and tighten using just your fingers.
Then tighten the set screw.
The lead screw should spin freely.
If not, then adjust the lock nut.
Attach the end plate using the original screws.
Don’t tighten it down yet – we need this loose so we can adjust it in a minute.
Pass the lead screw through the carriage and seat the bearing into the end plate.
Re-attach the motor end plate, again leaving it loose for the moment so we can adjust things.
Fasten the new lead screw nut to the carriage using the original screws.
Rotate the lead screw to move the carriage to the motor end plate and tighten the endplate
screws to lock its position in place.
Now move the carriage to the other end and tighten that end plate.
Move the carriage back and forth several times the full length of the rails to make sure
there isn’t any binding.
If there is some binding then just repeat the previous steps until it moves nice and
freely.
When you are happy with that, go ahead and do any final tightening, attach the motor
and tighten the shaft coupler.
Apply a little lubricant to the screw and rails and then have the motor move the carriage
up and down the slide a few times to spread the lubricant.
Step by step instruction on how to do all of this are on the product page right here.
If you have any questions about these linear slides, please contact AutomationDirect’s
free award winning tech support during regular business hours.
They will be happy to help.
And don’t forget the forums.
There are lots of folks there that love to share their years of experience.
Just don’t post any questions directed at AutomationDirect’s support team, they don’t
monitor the forums on a regular basis.