Hi, DIYers.
This is Michael from Alarm Grid, and today I'm
going to be showing you how to enroll a DSC PG9914 motion
detection sensor with a Qolsys IQ Panel 2 Plus security
system.
The DSC PG9914, it's a very popular motion detection
sensor, we include it with many of our Qolsys IQ Panel 2 Plus
kits, so there is a good chance that you have encountered this.
So it has a maximum detection area of 39 feet
and, like all other PowerG sensors,
it uses 128-bit AES encryption, and it
has a wireless communication range of up to 2,000 feet
away from the IQ Panel 2 Plus in an open air environment.
And it offers pet immunity for small animals weighing up
to 85 pounds.
So that's a little bit of information about the sensor,
so let's get into it.
Before we do anything on the IQ 2,
the first thing I want to show you
is just how we open up the sensor.
So you see there is a top and bottom,
and we're going to the bottom, and you
see that there's a crevice in the bottom
and this thing helps you-- this little semi-circle helps
you identify the center of it.
And you can just stick your fingernail into it like so,
and you can just press inward, and you can pop open
the sensor, just like that.
So we have our sensor open and we
will need to access the enrollment button, which
is next to the battery right there.
So we're going to be using that when
we go to enroll to the system.
But first, we have to put the system into its auto enrollment
mode, which is what I'm going to do now.
So we're at the main screen of the IQ Panel 2
Plus, we're going to click the small gray bar at the top,
we're going to choose Settings, we're
going to choose Advanced Settings
and then we're going to enter in our installer code, which
ours is at the default of 1111.
And we're going to choose installation,
we're going to choose devices, we're
going to choose security sensors,
and we're going to choose auto learn sensor.
Now, make sure you have CR123A battery installed,
this is also known as a camera battery,
so make sure the sensor is receiving power.
And what we're going to do, we're
going to press and hold the enrollment button until it
turns solid orange, and then we're going to release it,
and you're going to see we're going
to get the enrollment notification on the IQ Panel 2
Plus.
One thing I do want to point out,
if you are having trouble enrolling the sensor,
then you can try defaulting the sensor
and that would be done by pressing and holding
the enrollment button, and keep holding it,
even as it turns orange.
That's a different sensor, that's not a PowerG sensor,
so we're just going to choose cancel there.
Like I was saying, you can default the sensor
by pressing and holding the enrollment button,
you get three red blinks.
And that will default the sensor and then
you can try doing the enrollment process again,
the solid orange LED, because this is an encrypted sensor
so it can only be enrolled with one system at a time.
So if you are having trouble doing the enrollment process,
then defaulting can be a good idea.
But we are not going to need to default today,
we're just going to do the standard process.
And we're going to hold this button
until the LED turns orange.
I couldn't see because I have to show it in the camera,
so we're going to try again now.
Now it's orange, we're going to release and see
we get auto learn PowerG sensor, so I
pressed and held the enrollment button
until the lid turned orange.
So we get auto learn PowerG sensor,
we have the serial number on the screen,
and we're going to choose OK.
And now we're going to configure the zone settings.
So since we auto enrolled, we don't
need to change the sensor DL ID, that's
auto enrolled in, that's also known as the serial number.
The sensor type can be kept as motion.
The sensor group is important, this
is going to be how the system responds
when the sensor is faulted.
So the popular ones to use here are sensor groups
15, 17, 20 and 35.
We have an FAQ that explains sensor groups in more detail
if you want to get more information on them,
but I will just cover the default
one, 17, away instant motion.
That's basically going to have the system go
into immediate alarm if the sensor is faulted
while the system is armed away.
If the system's armed state, the sensor
will be automatically bypassed as an interior sensor, so
that way, you can move around the building
without worrying about triggering
an alarm on your system.
But if it is in armed away mode, then that
means there should be nobody inside the building.
And if the sensors faulted, then the system
will go into immediate alarm, you
won't get a chance to disarm, there won't be an entry delay,
so I will keep it at that one.
High traffic shutdown, that basically prevents the sensor
from repeatedly sending signals to the system when
it's faulted, it's done to conserve battery life.
You see, we have a variety of selections
here, you can set those as needed.
But we'll keep ours at the default of two minutes.
Sensor name, this is basically just used
to identify the sensor.
We can enter in a custom description, which we'll do
that, we'll call it bedroom--
and press the space --motion.
We'll use that as our name and we'll
press the green button there.
So our name is bedroom motion.
And then we can choose a chime type
if we want to get the system to produce a sound effect when
the sensor is faulted.
There's various ones in here, let's try on the hunt.
And that's what on the hunt sounds like, I'll try one more,
I'll try dear deer.
OK, we'll go with dear deer, that'll be our chime type.
You can also send it to none if you
don't want a chime, that's an option as well,
but choose whichever one you like.
Voice prompts will have the panel speak out the sensor name
when the censor's faulted, so that way,
it can give you a little bit more information.
Maybe you have multiple sensors set to dear deer,
and you don't know which one is which.
So then you hear a bedroom motion along with it,
and then you know, Oh, it's my bedroom motion,
there must be some activity in there,
so that can be useful for you.
And source, we'll keep that at PowerG because this is a PowerG
sensor.
So once we're done, we'll choose Add New,
and it's just going to finish adding the sensor.
And you see, it has been added successfully
and we are getting the dear deer sound effect because we
are moving the sensor around.
But I'm just going to close it, we
have the sensor aligned perfectly,
and we just close it.
And It's not aligned perfectly yet,
we'll get it so that it is.
OK, there, and then it snaps into place just like that,
and that's how we have our sensor closed.
And then we can return to the main screen
by pressing the house at the bottom.
And there you see our sensor is not active right now,
but if we just use All, then you do see,
we have the bedroom motion there.
So that bedroom motion is enrolled with the Qolsys IQ
Panel 2 Plus security system.
So that's how you pair a DSC PG9914 motion detection sensor
with a Qolsys IQ Panel 2 Plus.
If you have any questions about the DSC PG9914
or the IQ Panel 2 Plus, or all our monitoring services,
send an email to support@alarmgrid.com.
If you found this video helpful, make
sure to give it a thumbs up below to like the video.
And remember to subscribe to our channel for updates
on future videos.
We hope you enjoyed the video.
Thank you.