hey everyone drew with geoarm and i am back to talk to you about the 2gig gc2e and getting a
dw10e wireless door window contact which is encrypted of course connected and programmed into
this 2gig gc2e super easy to do we're going to go ahead and hit security on the main screen here
once you're in the security go ahead and hit menu and then you want to go into tool box once you're
in toolbox it's asking you here for your installer code mine is factory of one five six one that
should get us into programming once in programming go ahead and hit that right arrow twice we're
going to get into installer toolbox here once you get into installer toolbox you should be able to
see here see system configuration all right now once you hit system configuration
the first available zone or zone one actually is gonna appear on the screen um my that's my first
available zone but for for the sake of this video i'm just gonna go ahead and move it to zone three
you just hit the right arrow to change what zone number you want to program on in this case it is
zone three all right so we'll go ahead and we'll hit the down arrow it's asking the sensor three
type i am on sensor three right now and it just wants to know what its responsibility is gonna
be this is gonna be my front door so i do want that to have a little bit of a delay on it so
that way when everybody comes in and out of the door it's not immediately triggering the alarm
uh and you know causing a false alarm condition so i'm putting an entry exit delay on this
you can also set it as an instant and in that case you would set it as a perimeter if it is
an instant type device my case it will be delayed my front door i'm going to hit the down arrow now
it's going to ask you to select the equipment code these are are unique because the e-series doesn't
program like the other ones the equipment codes on e-series sensors will start with the number two
so in this case the equipment code is 2862 which is the e-series thin door and window contact and
once again that equipment code is 2862 for the e-series thin door window contact press the down
arrow after you've selected that it's going to ask you if you want this device to act as a normally
open device i do not press the down arrow now this is where we're going to learn it in it wants
you to either manually enter the serial number or learn it in i suggest learning it in just because
then you know the system has acknowledged it and is accepting it so i'm gonna grab my contact here
which of course i have on the side with the uh three perforations that's where the magnet goes
so i'm gonna leave it sitting like that and what we're gonna do is we're gonna hit shift on the
uh touch screen itself once you hit shift you'll see a bunch of new menus pop up over on this side
we're going to hit learn once we hit learn we're just going to remove the contact from the magnet
put it back and then it should automatically learn in we'll go ahead and we'll confirm that our tx
id is the correct tx id and it is zero four zero eight five four three in this case we'll put this
thing down you're gonna hit okay after you've done that you've confirmed the serial number is correct
you go ahead and you hit the down arrow now this is a new device so i am going to leave it as a new
device if it's a used device you can press the right arrow and set it as existing this is new
now you press the down arrow it's going to come to a question about loop numbers this is a a actual
question on here that gets a lot of uh you know misinformation or or whatever may happen but the
loop number for this device sitting by itself just like this without anything else connected to it it
will be a loop two device this will be operating as a wireless loop 2 device now the the way that
the loop would change in this regard is if you had to wire an external wire device into this because
it does accept external wire devices so you could wire a hardwired door window contact that would be
monitored through this wireless device if you want and if you did that it would become a loop one
instead of a loop two so we're gonna leave it loop two because i'm leaving it operational as is we're
gonna hit the down arrow now it wants to know if you would like an additional delay on this
device before it reports to the central station i don't like that so i'm not going to do it i'm
going to go ahead and press the right arrow to disable that then i'm going to hit the down
arrow at this point i want you to construct your voice description this is where it gets a little
tricky uh this is one of the more complicated things about doing it but uh still not very
difficult what you're gonna do is you're gonna hit insert when you hit insert the word abort is gonna
appear on there you just keep pressing the right arrow until you get to your desired descriptor in
this case it's going to be front door so i just keep hitting the right arrow until i get to front
sorry for the delay here it is a long way to get to it
all right and we have front and then we're going to insert again and then we're just
going to go to door just keep hitting the right arrow until you go to door
you can also scroll the other way if you're going into the other side of the alphabet but all right
so now i have front door in there now that that's in there i'm going to hit the down arrow
and it's going to ask if you want this to report i do want it to report because whenever
this device goes off i want it to send a signal to central station now if you're setting up like
a local type device or something like that you can just press the right arrow and disable reporting
then this device is only going to be local it's not going to report to anyone so in this case i
do want it to report so i'm going to hit the down arrow all right and then this question is asking
if you like the system to supervise this device so it's going to be monitoring for low battery for
tamper conditions uh loss of rf supervision that kind of thing so that's what this device is going
to be doing with this field so i do want that so we're going to leave that and press the down arrow
now this is where it's going to ask if you want it to chime i actually do want it to chime
i'm going to use the chime and the voice description so it's going to chime and then say
what the zone is and that is zero two so i'm gonna set that up and then i'm gonna hit the down arrow
at this point you've wrapped up the programming of your system of your sensor i'm sorry
so you can continue editing or adding sensors by clicking edit next or you can re-edit you know
the fields in this one by clicking edit current i don't want to do either one of those i'm just
going to hit skip and then i'm going to hit end because i don't want to do any more programming at
this point it's going to prompt you with another field and it's going to have a little save changes
uh icon at the bottom with a check mark i do want to save changes if you were in programming and you
don't really know what you did and you don't want to save your changes just uncheck that and then
you're going to hit exit at this point it's going to go through its reboot here and it once it comes
back up this device will be learned in so we're just going to wait for that reboot to occur here
all right and now that we have this device back here
and it's powered back on after it's reboot we can just test this so remove it there we go
okay let's close it and we'll open it again just to test it
all right and that ladies and gentlemen is how you program the dw10e-345
wireless encrypted door window contact into the 2gig gc2e security system if you guys have any
questions or any comments please leave them below other than that take care and have a great day
make sure to subscribe to our youtube page and click the show more tab underneath the
video where you can view valuable links pertaining to this product
similar how-to videos and our low-cost no contract alarm monitoring services