Brought to you by 1AAuto.com, your source for quality replacement parts and the best
service on the internet.
Hi, I'm Mike Green.
I'm one of the owners of 1A Auto.
I want to help you save time and money repairing and maintaining your vehicle.
I'm going to use my 20+ years' experience restoring and repairing cars and trucks like
this to show you the correct way to install parts from 1AAuto.com.
The right parts installed correctly, that's going to save you time and money.
Thank you and enjoy the video.
In this video we're going to show you headlight replacement both just replacing the headlight
bulbs and replacing the entire assembly.
This is a 2001 PT Cruiser exact the same for 2001 to 2005 and very similar for the 2006
and up cars.
Tools you'll need are a jack and jack stands, a 19mm socket and ratchet or your tire iron,
7mm and 10mm sockets with ratchets and extensions, flat blade screwdriver, needle nose pliers,
and painter's tape which is kind of optional.
You can see I have the car jacked up and the wheels off.
If you're just looking to replace the headlight bulb, this is not necessary.
What you want to do is if you're replacing the right-hand headlight bulb, you turn your
wheels all the way to the left and get your wheel over here and give you some space.
To just replace the bulbs you just kind of reach in here and pull this door down.
You kind of push that way and pull it off, and then right in here is your bulb.
Twist it counterclockwise and then pull it out, and then there's a little tab here just
kind of pull the bulb apart, and reinstall and plug it back in.
Install it into the light.
Kind of twist it around a little bit and make sure it goes into the socket properly, twist
it clockwise.
There's a bulb up here which is one of your signal bulbs, same thing.
Twist it counterclockwise.
Pull it out.
Bulb comes out, goes back in.
Work it in there.
Twist it clockwise and lock it in place.
Stop the action for just a second.
Right where that red arrow is pointing, that is your high beam bulb which I accidentally
forgot to kind of go over its location, and it's the same procedure as the other headlight.
Twist it counterclockwise and pull it out.
There's some tabs that hold the bulb into the harness and then you put it back in by
pushing it back into the socket and twisting clockwise.
And put this door back up in.
It slides in over there, and then this locks into place like that.
To replace your whole headlight assembly you'll want to remove the little pin at the bottom.
This is up near the bumper looking from the bottom of the car.
There's a pin that holds the lower plastic panel at the bottom.
Just use a screwdriver or if you use a pair of needle nose pliers, put it up in there
and pry that out.
Now there are three 7mm screws that you'll want to remove.
And we'll speed that up as we take out those 7mm screws, and then put that panel off to
the side.
Now there's three pins that hold part of the rest of the inner fender in, one there in
front of the shock, and then there's one up top kind of hidden in there.
I'm just going to pry it out with a screwdriver and then there's one more towards the back.
Change the angle here.
You want to pry those out with your screwdriver.
Some of the other videos show you just kind of ripping this fender, part of the fender
back.
Not a good idea easy enough to take it apart.
The next steps in taking it apart are five more 7mm bolts.
There's one up there, three down lower, and then one up underneath, and now that inner
fender comes right down and out.
What I'm doing here is - a couple of those push pins I wasn't able to get out with the
screwdriver, so I'm just using a pair of needle nose pliers.
Put them in underneath and pull them out.
So now we'll unplug our bulbs.
Now right up in here there are two 10mm bolts or nuts to remove here and here.
Fast forward as I remove those two 10mm nuts.
Now you have four 10mm bolts, and fast forward as I take those out.
You'll notice on the bottom right one it appears to stay there.
It unscrewed from the back of the headlight so after I took the headlight out I held it
with a pair of pliers and then used a wrench to get it off and then I used an extension
for that top left one.
Now with all the bolts out, your bumper cover will come down some.
You've got to work you light forward and down.
You'll probably have to push down a little extra right here and work your light up on
top of your fender cover and the light comes right out.
Here we've got the new headlight from 1A Auto.
If you're concerned about scratching your bumper cover just put a little blue painter's
tape on there, and then kind of put the outside in first, and the top in, and then actually
the outside goes in a little bit lower than where it's supposed to go and you basically
just kind of rotate the bottom straight up and in.
It's kind of a matter of you push it in there and then as you push it in and also you're
looking back here to see that everything's going in and lining up correctly and you just
kind of carefully pull this painter's tape up and out of here and get that off.
We'll fast forward a little bit here.
We just start those four nuts that hold the headlight assembly to the fender, and we'll
keep that pace going as we start the two 10mm nuts that hold the bumper cover up to the
fender.
Now you want to tighten those up first.
It kind of helps to push the light up into place, and then as you're tightening the four
nuts that hold the fender you can just make sure to look on the other side to make sure
the headlight is up where you want it and then tighten those.
You want them to be snug, but they don't have to be incredibly tight and then plug in your
bulbs and your signal light.
Here I'm just doing a final tightening and you can see I'm lifting up on that light and
making sure it's up in the right place as I tighten it up.
Now you put the inner fender in.
Put the pin in that holds it at the front to the front of the fender first.
Then line up the back and make sure it's lined up correctly with the holes and everything
to bolt it together.
Put that pin in that's behind the strut, and then start all your 7mm bolts in, and then,
of course, tighten those 7mm bolts.
And the last part of that step to the inner fender is putting that last pin in right there.
And then put the front close-out panel back up in place, and the three bolts that hold
it.
Also, I think I forget to film here, but there's also a push pin at the bottom that pushes
in, and then tighten those up nice and snug.
Now you'll want to put the wheel back on.
Start you lug nuts all by hand first to avoid cross-threading them, and then I use my impact
wrench just to tighten them preliminarily, and
then once the vehicle is back on the ground use a torque wrench to tighten the lug nuts
to 100 foot pounds using a star pattern.
We hope this helps you out.
Brought to you by www.1AAuto.com, your source for quality replacement parts and the best
service on the internet.
Please feel free to call us toll free, 888-844-3393.
We're the company that's here for you on the internet and in person.