Hi DIYers.
Sterling with AlarmGrid here, and today we're going to show you how to join your Lyric Security
System to your WiFi network.
So there is no WiFi module installation video for the Lyric because the beauty of the Lyric
is, they've built WiFi right into the box.
So there's no extra module to get.
It's built into the control panel and you just have to join to your network.
And the reason you would join to the network is for any kind of communications to alarm
monitoring services and/or Total Connect 2.0 services, if you want remote arming, disarming
or alerts, texts or emails from the system.
It does support cellular communications as well.
So if you didn't want to rely on just WiFi internet, you can back it up with a cell module
that fits into the side, and we'll show you that in a later video.
There is no hardwired internet option, so if you were concerned about the reliability
of WiFi, the solution is to use cellular.
But if you want to do internet only, then WiFi is what you're going to use.
There's two ways to join to the network.
One, is through the master programming and two, is through the installer level programming.
So just like on the LYNX Touch, you have two different security codes out of the box by
default.
From the home screen, we have security, automation, video, smart scenes, notices and settings.
So when we hit "settings," we can see brightness and volume.
When we hit "security," we're into our deeper level field, very similar to anyone that's
ever used the LYNX Touch.
We're going to hit "tools," slightly different screens but kind of similar functionality,
similar programming.
If we use our master code, by default it's "1234."
We're into our master level programming.
So Honeywell has not yet fully embraced the do-it-yourselfer to be the installer.
They're still restricting you to your master level programming with the master code.
And your programming or installer code gets you into the deeper level programming.
The idea is that if you have a local company to install this, they're going to give you
your master code so you can get in here and you can set up users.
You can check your event log.
You can do some more advanced stuff like changing batteries, adding cellular communicators,
you have your date and time selection, your reminder so you can put reminders for yourself
and you can do voice command setup as well.
So this panel, you can talk to it and have it interact with you through your voice.
And then, "WiFi config" is another thing that Honeywell assumes an end-user can do.
So on this screen, you have a few options.
You can scan for access points and the panel will actually look and say what WiFi networks
do I see?
And you can join to any network that it sees, that you have a password for.
You have a manual configure access point.
So if you had one without an SSID broadcast, you can manually config and connect that way.
And then finally, it does WPS encryption.
So if there was a digit or character in your security password for your router that this
system doesn't support, instead of typing in the security key, could do WPS encryption,
which normally entails pressing a button on the router, pressing a button on the panel
and then they talk to each other without having to type in a key.
We'll show you that in a separate video.
But for now we're going to show you the standard scan access points way to connect.
So we hit scan access points.
Sometimes it takes longer than others but eventually you should see all wireless networks
in range of the panel.
If you hit the down arrow, you can see we have quite a few networks.
We are in a town home complex, which makes sense, the houses are closer together and
we're picking up quite a few WiFi networks.
So in our case, we're going to grab this second network down, that's our network name.
And you highlight the network you want and at the bottom you hit "edit."
If you didn't see any networks you could hit "scan."
So if your router was powered down when you first scanned and you powered your router
up, hitting "scan" would rescan for networks.
But you do not have to hit "scan" because just hitting "scan access points" does the
scanning and shows you your list.
So as long as your network shows up here, you don't have to hit the "scan" separately.
So you highlight your network and you hit "edit."
Now, you can see the SSID name at the top, which we have blurred for security reasons.
You can see that the security level that the router is using is displayed here.
This is a selectable option, however, it should grab whatever network security the router
is using by default.
So you really should never change that.
And one thing we've noticed and talked to Honeywell about is that WEP security, which
is an older security protocol for routers, is an option.
If your router does WEP and it pops up WEP, it's because your router is set that way.
We do not recommend using WEP encryption at this time, okay?
We are still in beta, things can change by the time this panel's released and perhaps
WEP will be supported later, but for now we've seen some bugs and some sluggish panel behavior
when you're using WEP encryption or security.
And therefore, we're recommending that you use WPA2, which is by far the most popular
standard.
If you did have a really old router popping up WEP, we suggest looking at the router and
seeing if you could switch it to WPA or WPA2.
And if you can't, we really do urge you to look at possibly updating your router to one
that supports WPA.
It's going to work a lot better when your security is not set WEP, all right?
So WPA2 just means we have a security password to join to our network.
To type our password in we hit this "key" box, and you can see we have this touchscreen
keypad now.
I have my WiFi complicated network password here as a picture and I'm going to type it
in now.
So you can see it's got four little asterisks.
When we hit "clear," it wipes it out back to a default code ready to accept.
So you hit "clear" first, you have this button that'll toggle between letters and numbers.
When you're on letters, you also have this button that toggles between uppercase and
lowercase.
And we're going to use this keypad to type our network security.
All right.
Now we have our nice secure password, which we're obstructing and not showing you what
we're typing in here for customer security reasons.
We are also going to recommend they change their password.
But we now have our password and if we hit "save" followed by "join," as long as we've
typed in the right password, this should connect to our router.
You can see the WiFi indicator at the top left, that it's thinking, processing, working.
And we now have a nice successful "device has been successfully added to the network."
If we hit "OK" and we come back out we can see on our network we now have a checkmark
next to our nice four solid green bars of strong WiFi connectivity.
If we hit the back arrow all the way to the home screen, we now have a WiFi indicator
at the top left of the panel, which would alert you.
Or you could visually see how strong the WiFi signal strength is from this panel to the
router, all right?
So we told you, you can do that from the master code programming if you were to do "tools."
And instead of "1234," which is the default master, if you do "4112," which is the default
installer, you have this "save" screen.
We going to just ignore.
This is a screen that ties the panel to a dealer or a Honeywell provider or a Lyric
certified dealer.
It wants to associate to Honeywell's dealer website.
In this case we're just going to say "no" for now, and we're now in programming.
So if we hit "program," you can go into "comm diagnostics" and "configure WiFi."
And you have the same exact screens that we showed you through the master code programming.
And doing "scan access points," you'll see our network with the green check that we're
already joined.
But this is the other way.
If you're in the installer level programming, it's under "comm diagnostics," "configure
WiFi" and then you have the same ability to join to a network using the installer code
instead of the master code.
So, we exit out of programming and we are connected to our WiFi.
And so that is how you connect a Lyric all-in-one security system to your WiFi network using
the built-in WiFi capabilities of the panel and the security key method of scanning for
access points.
We hope you've enjoyed this video.
If you have any questions on connecting your Lyric system to your router, please let us
know.
And also we invite you to subscribe to our channel so you are up-to-date on all of the
new Lyric videos that we'll be releasing throughout this beta program.