Hi, DIYers. Sterling with Alarm Grid here and today we're going to show you how to install
the L5100-WiFi board, which is a Wi-Fi Internet communicator for a LYNX Touch Security System.
We have our LYNX Touch L5200 on our nice desk mount so that we can conveniently use the
panel from our kitchen counter. We are using the Honeywell LT-CABLE to provide power to
our panel, which you can see how to install that in our L5200 installation video. And
now we're going to show you how to install the Wi-Fi communicator.
The reason you would add this piece to your LYNX Touch System is if you wanted to get
Total Connect Service and/or Central Station Monitoring Service. The L5200 does not come
included with the Wi-Fi board. It is an add-on module. It fits inside the panel, allows you
to connect your unit with your Wi-Fi router, and then you can get monitoring services.
Total Connect is not available unless you have this unit or one of the other communication
paths, the ILP5 hardwired Ethernet cable communicator or the GSMVLP5-4G communicator. If you choose
to go Wi-Fi, it is a Wi-Fi connection back to your router. You do not need an Ethernet
cable. And as a backup path, you can marry the Wi-Fi with the GSM for the most secure
communication path. It would be Wi-Fi primary, cellular backup.
So now that we've explained why you would be getting one of these units, we're going
to show you how to install it. First thing you need to do is open up the L5200. To do
so, just like on every LYNX Touch, there are two tabs on the top. Simply depress one tab,
pressing forward towards the front of the panel. You'll hear a cover tamper, and it'll
start to beep to alert you that someone opened it. You can press the button at the home,
the home button, to silence that beeping. And then you do the same to the second tab.
The front panel swings down. We have our LT-CABLE providing AC power here. We have our battery
connection here. Before we install our Wi-Fi, we always want to power the system down. So
we're going to disconnect our LT-CABLE. We're going to disconnect our battery. Now the panel
is powered down. You look at the front. It's dark. No buttons work.
To install the Wi-Fi, it always sits underneath the speaker. If you install it on the wrong
side, because there is a matching connector on this side, it's tough to tell because we
have our Z-Wave module in there. But if I just slide the Z-Wave out, you can see there
are matching connectors, so that is a point of confusion; Z-Wave always on the left, Wi-Fi
always on the right. So the Wi-Fi sits in this little slot, and you just put a little
pressure on the right side of this black connector, force it into the board as much as it will
go, and it sits right under the speaker.
Before you close the panel, you should make note of the MAC and CRC numbers which are
displayed on a sticker on the Wi-Fi board. You can find those same numbers on the side
of your Wi-Fi box. The MAC address always starts 00 delta 0 two delta and then it's
a custom six digits after that. And the CRC is an alphanumeric four-digit number. Those
are the two pieces of information you will have to give to your monitoring company for
them to activate your Wi-Fi communicator. We should also note that Rev 5.0.6 is the
version of the L5100 Wi-Fi board that you need when you're doing the L5200 control panel.
So now that we're installed, we know how to find our MAC and our CRC, we're going to power
the system up. First we plug in our AC power. Then we plug in our DC battery. We close up
the panel, and we wait for it to boot. It goes through the normal boot sequence. We
come up with red, system standby. We can give it a minute, and it will go over to green,
ready to arm. Or if we don't want to wait, we press and hold the home button, forces
over to ready to arm in green. You'll notice that we now have a Wi-Fi indicator icon on
the main home page. The system sees that it's got a Wi-Fi board, and it will show you whether
or not you're connected to the Internet. You will need to connect to the Internet before
you activate your monitoring, but that is how you physically install the L5100-Wi-Fi
module.
If you have any questions, send us an email at support@alarmgrid.com and make sure to
subscribe to our channel to see all the rest of our LYNX Touch installation videos.